2022-08-10

Height Adjuster - Seat Belt - LH (Remove and Replace)

Correction code 200500320.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door.
  2. Lower the LH front window.
  3. Open LH falcon wing door.
  4. Move the LH front seat backwards.
  5. Release the LH front door seal from the B-pillar trim.
  6. Release the clips (x5) that attach the upper portion of the LH lower B-pillar to the LH upper B-pillar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool
  7. Release the clips (x3) and magnets (x2) that attach the LH upper B-pillar trim to the B-pillar, and then disconnect the LH falcon wing door button electrical connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool
    • Pocket screwdriver
  8. Move the LH upper B-pillar trim aside.
  9. Remove and discard the nut that attaches the LH 1st row upper seatbelt to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 17 mm deep socket
    • Ratchet/torque wrench
  10. Remove and discard the bolts (x2) that attach the LH seat belt height adjuster to the vehicle, and then remove the adjuster from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
    • Ratchet/torque wrench

Install

  1. Position the LH seat belt height adjuster on the vehicle, and then install the new bolts (x2) that attach the adjuster to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  2. Install a new nut that attaches the LH 1st row upper seatbelt to the vehicle.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 17 mm deep socket
    • Ratchet/torque wrench
  3. Connect the LH falcon wing door button electrical connector, and then install the clips (x3) and magnets (x2) that attach the LH upper B-pillar trim to the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace the clips if damaged.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the seat belt through the LH seat belt height adjuster opening, and then align the height adjuster slider to adjustable D-ring.
  4. Install the clips (x5) that attach the upper portion of the LH lower B-pillar to the LH upper B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace clips if damaged.
  5. Fully seat the LH front door seal on the B-pillar trim.
  6. Move the LH front seat to original position.
  7. Close the LH falcon wing door.
  8. Raise the LH front window.
  9. Close the LH front door.