22/09/2022 14:24:58

Reflex Marker - Taillight - RH (Global) (Remove and Replace)

Correction code 17400042 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Informational PurposesAn informational icon, calling your attention
Note
This procedure is for the Global Refresh version of this part. The procedure for the Original version of this part is here: Reflex Marker - Taillight - RH (Remove and Replace).
  1. Open RH front door
  2. Move RH front seat forward
  3. Open RH falcon wing door
  4. Move RH Monopost seat forward
  5. Remove RH rear sill assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, 1x datum
  6. Open liftgate
  7. Remove trunk rear load floor
  8. Remove trunk tub floor insulator
  9. Remove trunk carpet
  10. Remove LH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x datum
  11. Remove RH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x datum
  12. Remove RH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm, 9x clips
  13. Remove RH lower C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T25, 2.5 Nm, 2x screws, T20, 2 Nm, Discard patch bolt after removal
  14. Remove trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 2x patch bolts, T25, 2.5 Nm, Discard patch bolts after removal
  15. Remove rear wall load support
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips, 2x clips
  16. Fold RH 3rd row seat back into down position
  17. Remove fasteners securing RH upper C-pillar trim to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x screws, T20, 2 Nm, 1x patch bolt, T25, 3 Nm, Discard patch bolt after removal
  18. Remove RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x datum
  19. Release RH trunk tie down from RH side trim carpet
  20. Remove RH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 4x push clips
  21. Remove RH trunk side trim bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, T30, 2.5 Nm, 1x screw, T20, 2.5 Nm, 1x push clip
  22. Disconnect RH body side tail lamp
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Disengage red locking tab
  23. Remove nuts securing RH tail lamp to body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 8mm, 3.5 Nm, Be cautious and do not drop the fasteners into vehicle body
  24. Remove RH body tail lamp from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, Note one datum clips into charge port door assembly
  25. Remove nut securing RHS reflex lens assembly to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 8mm, 1 Nm
  26. Remove RHS reflex lens assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, Carefully release the front datum next to locator pin before proceeding onto the rear datums to prevent damaging the surface of body
  27. Position RHS reflex lens assembly onto vehicle_x000A_
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, Press gently to ensure datums are fully seated into grommets
  28. Install bolt securing RHS reflex lens assembly to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 8mm, 1 Nm
  29. Secure RH body tail lamp onto vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, Note one datum clips into charge port door assembly
  30. Install nuts securing RH tail lamp to body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 8mm, 3.5 Nm, Be cautious and do not drop the fasteners into vehicle body
  31. Connect body side tail lamp connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Engage red locking tab
  32. Install RH trunk side trim bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, T30, 2.5 Nm, 1x screw, T20, 2.5 Nm, 1x push clip
  33. Install RH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 4x push clips
  34. Insert RH trunk tie down into RH trunk side trim carpet
  35. Install RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x datum
  36. Install fasteners securing RH upper C-pillar trim to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x screws, T20, 2 Nm, 1x patch bolt, T25, 3 Nm, Install new patch bolt
  37. Raise RH 3rd row seat back into the upright position
  38. Install RH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T25, 2.5 Nm, 2x screws, T20, 2 Nm, Install new patch bolt
  39. Install RH rear sill assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, 1x datum
  40. Install RH mid C-Pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm, 9x clips
  41. Install rear wall load floor support
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips, 2x clips
  42. Install rear trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 2x patch bolts, T25, 2.5 Nm, Make sure to seat liftgate seal properly, Install new patch bolts
  43. Install RH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x datum
  44. Install LH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x datum
  45. Install trunk carpet
  46. Install trunk tub floor insulator
  47. Install trunk rear load floor
  48. Close liftgate
  49. Move RH Monopost seat to original position
  50. Close RH falcon wing door
  51. Move RH front seat to original position
  52. Close RH front door