Correction code 17102812 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

1. Open the LH front door.
2. Lower the LH front window.
3. Lower LH rear window
4. Open LH falcon wing door
5. Remove LH falcon door lower garnish
   Note

   9x V-clips, Replace any damaged or missing clips, Take care not to damage door trim panel during removal

   

   

6. Remove LH rear decor trim panel
   Note

   7x clips, 2x connectors

   

   

   

7. Remove bolts securing LH rear door panel to door
   Note

   8x bolts, 10mm, 6 Nm

   

8. Raise LH rear window
9. Open the hood.
10. Power off the vehicle using the touchscreen.

    

11. Remove the rear underhood apron.

    

    

12. Disconnect the LV battery connector and First Responder Loop.

    

    

    

13. Remove LH rear door trim panel
    Note

    13x clips, 2x connectors

    

    

14. Disconnect 2nd row head air bag connector
    Note

    1x connector, Release orange lock and then disconnect

    

15. Remove bolts securing LH closeout panel to falcon door
    Note

    10x bolts, T25, 8mm, 1.8 Nm

    

    

16. Release window motor from LH closeout panel
    Note

    3x screws, T30, 1.8 Nm

    

17. Disconnect ultrasonic ECU
    Note

    1x connector, Release black locking tab

    

18. Disconnect LH rear door controller
    Note

    2x connectors

    

19. Release clips securing lower falcon door harnesses and connectors to LH closeout panel
    Note

    7x clips

    

20. Release emergence release cable
    Note

    Unclip and feed door release cable through LH closeout panel

    

21. Release LH rear closeout panel
    Note

    2x tabs, Pull LH closeout panel away from door and lift window motor up to release

    

    

22. Remove bolts securing LH actuator and pull actuator up to gain access, disconnect cinch actuator
    Note

    1x connector, 3x nuts, 10mm, 3 Nm

    

    

23. Disconnect window regulator motor
    Note

    1x connector

    

24. Remove speaker from LH rear door
    Note

    4x bolts, T25, 4 Nm, 2x datums, 1x connector

    

    

    

25. Disconnect LH falcon door close switch
    Note

    1x connector

    

26. Disconnect LH falcon door rear pinch sensor connector
    Note

    1x connector

    

27. Disconnect clip from LH lower latch cover
    Note

    1x clip

    

28. Remove LH lower latch cover
    Note

    1x latching tab

    

    

29. Disconnect LH lower latch connector
    Note

    1x connector

    

30. Disconnect LH falcon door front pinch sensor
    Note

    1x connector

    

31. Disconnect LH outer door handle carrier connector
    Note

    1x connector

    

32. Disconnect LH ultrasonic sensor connector
    Note

    1x connector, Do not use pry tool on tri pod

    

    

33. Remove LH rear door lower harness
    Note

    8x fasteners, 1x plug

    

    

34. Install LH rear door lower harness
    Note

    8x fasteners, 1x plug

    

    

35. Connect LH ultrasonic sensor
    Note

    1x connector, 1x clip, Engage red locking tab after securing connect

    

    

36. Connect LH outer door handle carrier connector
    Note

    1x connector

    

37. Connect LH front pinch sensor connector
    Note

    1x connector

    

38. Connect LH lower latch connector
    Note

    1x connector

    

39. Install LH lower latch cover
    Note

    1x latching tab

    

    

40. Attach clip to LH lower latch cover
    Note

    1x clip

    

41. Connect LH rear pinch sensor connector
    Note

    1x connector

    

42. Connect LH falcon door close switch connector
    Note

    1x connector

    

43. Install LH falcon door speaker
    Note

    4x screws, T25, 4 Nm, 1x connector

    

    

    

44. Connect LH window regulator motor connector
    Note

    1x connector

    

45. Connect and install LH cinch actuator
    Note

    3x nuts, 10mm, 3 Nm

    

    

46. Install release cable through LH closeout panel

    

47. Position LH window motor onto back of closeout panel
    Note

    2x tabs

    

    

48. Install window motor to closeout panel
    Note

    3x screws, T30, 1.8 Nm

    

49. Install LH closeout panel
    Note

    10x bolts, T25, 8mm, 1.8 Nm

    

    

50. Connect ultrasonic ECU
    Note

    1x connector, securing locking tab

    

51. Connect LH 2nd row head air bag connector
    Note

    1x connector, Engage locking tab

    

52. Connect LH rear door controller
    Note

    2x connectors

    

53. Install clips securing harnesses and connectors to LH closeout panel
    Note

    7x clips

    

54. Install LH rear door trim panel
    Note

    2x connectors, 13x clips, Install door trim starting from top and make sure the door trim tab is fitted correctly on the inner belt seal

    

    

55. Install bolts securing LH rear door panel to door
    Note

    8x bolts, 10mm, 6 Nm

    

56. Install LH rear door decor trim panel
    Note

    7x clips, 2x connectors, Take care not to damage door trim panel

    

    

    

57. Install LH rear lower door garnish
    Note

    9x V-clips

    

    

58. Connect the First Responder Loop and LV battery connector.

    

    

59. Install the rear underhood apron.

    

    

60. Close the hood.
61. Close LH falcon door
62. Raise the LH front window.
63. Close the LH front door.