09/09/2022 14:57:06
Air Vent - Instrument Panel - Driver (LHD) (Remove and Replace)
Correction code
18100032
1.44
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate Times to learn
more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.
NOTE: See Personal Protection to make sure proper PPE is worn when
performing the below
procedure.
Warning
This procedure is a DRAFT,
although it has been validated. Warnings and Cautions might be missing. Follow safety
requirements and use extreme caution when working on or near high voltage systems and
components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
- Open LH front door
- Lower LH and RH front windows
- Move LH front seat backward
-
Remove LH IP end cap
Note7x clips, 1x datum, Ensure clip at IP carrier is released fully before removal
-
Remove LH mid A-pillar trim
Note2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
-
Remove IP LH mid panel
Note6x tabs
-
Remove LH sunvisor bezel
Note6x clips, 1x tab, Release clips, then slide bezel towards front of vehicle to release
-
Remove bolts securing LH upper A-pillar to body
Note2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Discard nut after removal
-
Remove LH upper A-pillar from vehicle
Note1x connector, 2x datums, Rotate pillar inboard to access connector, Release datums upward out of IP sub assembly
-
Adjust steering column fully rearward and fully down
NoteVia UI > Controls > Steering , Use left steering wheel scroll wheel to adjust steering column
-
Open RH front door
-
Move RH front seat backward
-
Open hood
NoteVia center display > Controls > Frunk Open
-
Power off vehicle via center display
NoteControls > Safety & Security > Power Off
-
Remove rear underhood apron
Note11x clips, 2x datums
-
Disconnect LV battery connector and First Responder Loop
Note2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL
-
Remove RH IP end cap
Note3x clips
-
Remove RH mid A-pillar trim
Note2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
-
Remove RH front sill plate
Note8x clips, 3x datums
-
Remove RH lower A-pillar trim
Note1x bolt, T25, 5 Nm, 2x clips, 1x datum
-
Remove RH sunvisor bezel
Note6x clips, 1x tab, Release clips, then slide bezel towards front of vehicle to release
-
Remove bolts securing RH upper A-pillar to body
Note2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Discard nut after removal
-
Remove RH upper A-pillar from vehicle
Note1x connector, 2x datums, Rotate pillar inboard to access connector, Release datums upward out of IP sub assembly
-
Release phone dock
Note4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel
-
Remove phone dock
Note3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage
-
Release IP service panel
Note2x tabs, 4x datums, Release top tabs and slide rearward
-
Release diagnostic and CAN harnesses from IP service panel
Note2x clips
-
Remove IP service panel
Note1x connector
-
Remove center display bracket bolts
Note2x bolts, 10mm, 11.5 Nm
-
Remove center display shroud
Note3x tabs, Slide display outwards until shroud fully clears IP and support, Release the bottom tabs and pull upward
-
Release center display coax and power connectors
Note2x connectors, 1x clip, Slide display rearward outwards from IP bracket and support during connector release
-
Remove center display
NoteSlide rearward, Place on soft clean surface
-
Remove IP closeout panel
Note4x tabs
-
Remove IP RH mid Panel
Note14x tabs, 2 datums
-
Remove IP Decor
Note21x clips, 6x datums, 4x connectors, Release each IP decor connector clip from IP carrier then disconnect from IP harness
-
Remove RH front floor mat
-
Remove RH footwell cover
Note3x magnets, 1x connector, 4x datums
-
Remove RH console side carpet
Note11x clips, 2x datums
-
Remove fasteners securing RH knee air bag assembly to vehicle
Note2x bolts, 10mm, 8 Nm, 1x clip
-
Remove the RH knee air bag assembly from vehicle
Note2x connectors, 1x clip, 6x tabs
-
Release glove box
Note5x screws, T20, 3 Nm
-
Release glove box connectors
Note3x connectors
-
Remove USB outlet
Note2x screws, T20, 3 Nm, 1x clip
-
Remove glove box
-
Release passenger IP air duct temperature sensor connector
Note1x connector
-
Remove passenger IP air duct
Note2x push-pull rivets
-
Remove IP carrier cross beam screws
Note2x bolts, 10mm, 3 Nm
-
Release passenger IP airbag connectors
Note3x connectors, Pull down spring loaded locks simultaneously to release airbag connectors
-
Release RH lower instrument panel
Note3x screws, T20, 3 Nm
-
Release center lower instrument panel
Note6x screws, T20, 3 Nm
-
Release LH lower instrument panel
Note3x screws, T20, 3 Nm
-
Release instrument cluster harness
Note1x connector, 1x clip
-
Release IP trim harness
Note1x connector, 1x clip
-
Position lower instrument panel assembly away from IP sub-assembly
Note6x datums, Move top edge as far rearward as possible without excessive stress on assembly
-
Release IP ground harness
Note1x clip, 1x bolt, 10mm, 9 Nm, Note routing behind center display RH bracket
-
Remove IP sub-assembly
NoteSlide IP sub-assembly rearward, Lift assembly up from IP carrier, Ensure airwave vents and passenger air bag are clear of lower IP assembly, Remove assembly out through RH front door, Recommend assistance as needed
-
Release air wave ventilation connectors
Note4x connectors, Place IC sub-assembly upside down on a protective surface to access connectors
-
Release aero glass assembly from IP sub-assembly
Note5x screws, T20, 2.5 Nm
-
Rotate aero glass assembly from IP sub-assembly
Note8x tabs, Rotate IP sub-assembly forward to release tabs
-
Remove aero glass assembly from IP sub-assembly
-
Remove driver vent assembly
Note5x screws, T20, 2 Nm
-
Install driver vent assembly to aero lens assembly
Note5x screws, T20, 2 Nm
-
Position aero glass assembly into IP sub-assembly
Note8x tabs, Align 8 tabs from IP sub-assembly into aero lens assembly
-
Rotate aero glass assembly to IP sub-assembly
Note8x tabs, Rotate IP sub-assembly rearward to engage tabs
-
Secure aero glass assembly to IP sub-assembly
Note5x screws, T20, 2.5 Nm
-
Secure air wave ventilation connectors
Note4x connectors
-
Install IP sub-assembly
Note4x datums, Slide IP sub-assembly into vehicle, Ensure passenger air bag and driver vent assembly have clearance past lower IP assembly, Engage IP sub-assembly datums into dash slots, Recommend assistance
-
Secure IP ground harness
Note1x clip, 1x bolt, 10mm, 3.5 Nm, Note routing behind center display RH bracket
-
Secure IP trim harness
Note1x connector, 1x clip
-
Secure instrument cluster harness
Note1x connector
-
Position lower instrument panel assembly into IP sub-assembly
-
Secure LH lower instrument panel
Note3x screws, T20, 3 Nm
-
Secure center lower instrument panel
Note6x screws, T20, 3 Nm
-
Secure RH lower instrument panel
Note3x screws, T20, 3 Nm
-
Install IP carrier cross beam bolts
Note2x bolts, 10mm, 3 Nm
-
Secure passenger IP airbag connectors
Note3x connectors
-
Install passenger IP air duct
Note2x push-pull rivets
-
Secure passenger IP air duct temperature sensor connector
Note1x connector
-
Install IP Decor
Note21x clips, 6x datums, 4x connectors, Connect ambient bright harness, Secure each IP decor connector clip to IP carrier, Secure IP decor to lower instrument panel
-
Secure USB outlet
Note2x screws, T20, 2 Nm, 1x clip, Ensure USB socket flush in glove box
-
Secure glove box connectors
Note3x connectors, Route harness through glove box datums
-
Install glove box
Note5x screws, T20, 3 Nm
-
Install RH knee air bag assembly into vehicle
Note2x connectors, 6x tabs, 1x clip, Hook tabs before fully seating, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector
-
Install fasteners securing RH knee air bag assembly to vehicle
Note2x bolts, 10mm, 8 Nm, 1x clip
-
Install RH console side carpet
Note11x clips, 2x datums
-
Install RH footwell cover
Note3x magnets, 4x datums, 1x connector
-
Install RH lower A-pillar trim
Note1x bolt, T25, 5 Nm, 2x clips, 1x datum
-
Install RH front sill plate
Note8x clips, 3x datums
-
Install RH front floor mat
-
Install RH upper A-pillar to vehicle
Note1x connector, 2x datums, Secure RH upper A-pillar harness, Align datums into IP sub assembly, Rotate upper A-pillar panel into position
-
Install bolts securing RH upper A-pillar to body
Note2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Install new nut
-
Install RH sunvisor bezel
Note6x clips, 1x tab, Insert tab and slide bezel towards rear of vehicle, then secure clips
-
Install RH mid A-pillar trim
Note2x clips, 3x datums, Verify weather seal is seated properly
-
Install RH IP end cap
Note3x clips
-
Install IP RH mid Panel
Note14x tabs, 2 datums
-
Install IP closeout panel
Note4x tabs
-
Route display harness behind LH display bracket
-
Secure center display coax and power connectors
Note2x connectors, 1x clip, Ensure strain relief clip is secure to linkage arm, Replace clip if damaged
-
Install center display shroud
Note3x tabs, Slide display downward until shroud tabs fully engages
-
Secure center display to IP carrier
Note2x bolts, 10mm, 11.5 Nm, Slide center display into IP carrier, Start RH bolt first
-
Secure IP service panel connector
Note1x connector
-
Secure diagnostic and CAN harnesses to IP service panel
Note2x clips
-
Install IP service panel
Note2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP
-
Install phone dock connections
Note3x connectors, 1x clip
-
Install phone dock
Note2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console
-
Connect First Responder Loop and LV battery connector
Note2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage upper locking tab when fully seated
-
Install rear underhood apron
Note11x clips, 2x datums
-
Close hood
- Move RH front seat to original position
- Close RH front door
-
Install LH upper A-pillar to vehicle
Note1x connector, 2x datums, Secure LH upper A-pillar harness, Align datums into IP sub assembly, Rotate upper A-pillar panel into position
-
Install bolts securing LH upper A-pillar to body
Note2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Install new nut
-
Install LH sunvisor bezel
Note6x clips, 1x tab, Insert tab and slide bezel towards rear of vehicle, then secure clips
-
Install IP LH mid panel
Note6x tabs
-
Install LH mid A-pillar trim
Note2x clips, 3x datums, Insert mid A-pillar trim into lower A-pillar trim, Secure clips into upper A-pillar and IP sub assembly, Verify weather seal is seated properly
-
Install LH IP end cap
Note7x clips, 1x datum
-
Adjust steering column back to original position
NoteVia UI>Controls>Steering , Use left steering wheel scroll wheel to adjust steering column
- Move LH front seat to original position
-
Calibrate the rear doors.
NoteIf the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
- Raise LH and RH front windows
- Close LH front door