10/12/2024 13:35:40

Door Glass - Rear - LH (Remove and Replace)

Correction code 11500302 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-12-10: Added new caution about Pre-Installation Glass Inspection service requirements.
  • 2023-05-24: Added cleaning instructions to prevent glass damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in Pre-Installation Glass Inspection before beginning this procedure.

Remove

  1. Lower the LH rear window.
  2. Open the LH rear door partially.
  3. Remove the LH rear outer belt trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    Starting from the rear edge, lift and roll the trim outward slowly and evenly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to bend or damage components.
  4. Open the LH falcon wing door.
  5. Remove the LH rear door trim lower garnish. See Garnish - Lower - Door Trim - Rear - LH (Remove and Replace).
  6. Remove the LH rear door trim decor. See Decor - Trim - Rear Door - LH (Remove and Replace).
  7. Remove the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  8. Set the LH Falcon door at a comfortable working height.
  9. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  10. Disconnect LV power. See LV Power (Disconnect and Connect).
  11. Remove the LH rear door inner belt seal.
  12. Release the orange locking tab, and then disconnect the LH falcon wing door air bag electrical connector.
  13. Remove the screws (x10) that attach the LH rear door closeout panel to the LH rear door.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  14. Remove the screws (x3) that attach the LH rear window motor to the LH rear door closeout panel.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  15. Release the tabs (x2) that attach the LH rear door closeout panel to the LH rear door, pull the closeout panel away from door, and then lift the window motor upward to release it.
  16. Release the black locking tab, and then disconnect the LH falcon wing door protection ECU.
  17. Disconnect the electrical connectors (x2) from the LH falcon wing door module.
  18. Release the clips (x7) that attach the harnesses and connectors to the LH rear door closeout panel.
  19. Release the clip, and then feed the door release cable through the LH rear door closeout panel.
  20. Loosen the nut that attaches the front of the glass to the regulator.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The nut does not need to be fully removed. If required, power the vehicle back on and use the window switch tool to move the regulator for nut access.
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  21. Partially close the LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not engage the latch.
  22. With assistance, release the clip that attaches the rear of LH rear door glass to the regulator, and then remove the glass from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Working from the outside of the vehicle, pull the front of the glass towards the rear of the vehicle, and then lift the glass out from the door.

Install

  1. Inspect the regulator for glass splinters or other debris, and clean it if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  2. With assistance, carefully position the LH rear door glass into the LH rear door, and then seat the glass into the rear clip and forward brace.
  3. Verify the LH rear door glass fitment, and then torque the nut that secures the front of the glass to the regulator.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  4. Feed the door release cable through the LH rear door closeout panel, and then secure the clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lubricate the cable grommet to aid in installation.
  5. Position the LH rear door window motor onto the back of the closeout panel, and then secure the tabs that attach the motor to the closeout panel.
  6. Install the screws (x3) that attach the LH rear window motor to the LH rear door closeout panel.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  7. Install the screws (x10) that attach the LH rear door closeout panel to the LH rear door.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  8. Connect the LH falcon wing door protection ECU electrical connector, and then engage the locking tab.
  9. Connect the LH falcon wing door air bag electrical connector, and then engage the orange locking tab.
  10. Connect the electrical connectors (x2) to the LH falcon wing door module.
  11. Install the clips (x7) that attach the harnesses and connectors to the LH rear door closeout panel.
  12. Install the LH rear door inner belt seal.
  13. Manually partially close the LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not engage the latch.
  14. Install the LH rear door outer belt trim.
  15. Connect LV power. See LV Power (Disconnect and Connect).
  16. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  17. Raise the LH rear window.
  18. Test that the LH rear window is functioning correctly.
  19. Check the LH rear window fitment and adjust as necessary.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to CVIS for latest specifications.
  20. Install the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  21. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors