15/08/2022 13:41:16

Harness - Seat Back - 3rd Row - LH (Remove and Replace)

Correction code 17107502 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH falcon wing doors.
  2. Open the liftgate.
  3. Fold the 2nd row 40 and 60 seats downward.
  4. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  5. Remove the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  6. Remove the rear trunk carpet. See Carpet - Rear Trunk (7 Seat) (Remove and Replace).
  7. Fold the LH and RH 3rd row seats downward.
  8. Remove the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
  9. Release the tabs (x4), fir tree clips (x2), and J hook that attach the lower section of the LH 3rd row seat upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the tabs inward, and then upwards to release.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  10. Disconnect the LH 3rd row seat connectors (x2), and then re-route the connectors through the lower section of the upholstery.
  11. Route the LH 3rd row seat connectors (x2) around the lower section of the upholstery, and then connect the connectors.
  12. Unfold the LH 3rd row seat to original position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Leave the headrest in folded position.
  13. Release the J-hook clip that attaches the upper half of the LH 3rd row seat upholstery to the seat.
  14. From the 3rd row, pull the inner portion of the seat cover and foam outward to gain access to the LH 3rd row seat recliner actuator.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution to not snag the J-hooks. The actuator is located on the front side of the seat back under the upholstery and cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the fold function to feed the bottom of the seat upholstery forward.
  15. Disconnect the LH 3rd row linear headrest actuator connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress both locking tabs on the side of the connector to release.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  16. Disconnect the LH 3rd row recliner actuator connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress both locking tabs on the side of the connector to release.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  17. From the 3rd row, pull the top outer portion of the seat cover and foam outward to gain access to LH 3rd row seat escutcheon.
  18. Carefully pull the LH 3rd row seat escutcheon forward to expose the LH 3rd row seat switch connector, and then disconnect the connector.
  19. Release the clips (x4) that attach the LH 3rd row seat back harness to the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  20. Remove the LH 3rd row seat back harness from the seat frame, and then remove the harness from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Feed the harness through the opening at the bottom of the seat frame to remove.

Install

  1. Position the LH 3rd row seat back harness on the seat frame, and then install the clips (x4) that attach the harness to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Feed the harness through the opening at the bottom of the seat frame to install.
  2. Connect the LH 3rd row seat back switch connector, and then install the 3rd row seat escutcheon into the seat back cushion trim.
  3. From the 3rd row, fold back the top outer portion of the LH 3rd row seat cover and foam over the seat frame.
  4. Connect the LH 3rd row recliner actuator connector.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  5. Connect the LH 3rd row linear headrest actuator connector.
  6. Fold the seat upholstery and cushion assembly over the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the folding function to assist with tucking the upholstery.
  7. Disconnect the LH 3rd row seat connectors (x2), and then route the connectors through the seat upholstery.
  8. Connect the LH 3rd row seat connectors (x2).
  9. Engage the tabs (x4), fir tree clips (x2), and J hook that attach the lower section of the LH 3rd row seat upholstery to the seat.
  10. Install the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
  11. Install the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
  12. Install the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  13. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  14. Unfold the LH and RH 3rd row seats into original position.
  15. Close the liftgate.
  16. Unfold the 2nd row 40 and 60 seats into original position.
  17. Close the LH and RH falcon wing doors.