Actuator - EZ Entry - 40 Track - 2nd Row Seat (7 Seat) (Remove and Replace)
Correction code 13020022 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Open the RH front door.
- Lower the RH front window.
- Move the RH front seat forward.
- Open the RH falcon wing door.
-
Starting from the bottom, carefully pry the 2nd row 40 seat escutcheon away from the
seat back to release the clips (x2), and then remove the escutcheon from the seat.
- Fold the 2nd row 40 seat downwards.
-
Release the J-hook that attaches the 2nd row 40 seat back upholstery to the
seat.
NoteFold the backrest upholstery down upon release.Tip: Use of the following tool(s) is recommended:
- 6in 90 degree tip miniature soft grip pick
-
Unzip the 2nd row 40 seat back upholstery on the LH and RH sides of the backrest
cover.
NoteEnds of the zippers are tucked underneath the seat upholstery. Use a pick to aid in moving the zippers.Tip: Use of the following tool(s) is recommended:
- 6in 90 degree tip miniature soft grip pick
-
Release the clips (x5) and Velcro strips (x2) that attach the 2nd row 40 seat plastic
seat back to the seat, and then remove the plastic seat back from the seat.
NoteFold the backrest cover over the headrest for access.Tip: Use of the following tool(s) is recommended:
- Clip pry tool
-
Release the clip that attaches the 2nd row 40 seat harness to the seat frame.
Tip: Use of the following tool(s) is recommended:
- Clip pry tool
-
Relieve the tension on the metal clip by moving the 2nd row 40 seat actuator slider
into the housing, and then remove and discard the metal clip from the actuator
slider.
Tip: Use of the following tool(s) is recommended:
- Plastic trim tool
- Small flat head screwdriver
-
Release the 2nd row 40 seat actuator slider cable from the slider.
CAUTIONUse caution not to damage the cable locating plastic.Tip: Use of the following tool(s) is recommended:
- Plastic trim tool
-
Release the clips (x2) that attach the 2nd row 40 seat actuator slider to the seat
frame.
NoteUse of the following tool(s) is recommended:
- Clip pry tool
-
Move the 2nd row 40 seat actuator slider towards the cable to relieve tension.
CAUTIONDo not kink or damage the cable.
-
Flip the 2nd row 40 seat actuator slider vertically, use a pick to release the cable
end fitting from the open slot, and then remove the slider from the vehicle.
CAUTIONDo not kink or damage the cable.Tip: Use of the following tool(s) is recommended:
- 6 in 90 degree tip miniature soft grip pick
-
Disconnect the 2nd row seat 40 track EZ entry actuator connector.
-
Remove the screws (x2) that attach the 2nd row seat 40 track EZ entry actuator to the
bracket.
Tip: Use of the following tool(s) is recommended:
- Flex head ratchet/flex head torque wrench
- Torx T15 socket
-
Release the tabs (x3) that attach the 2nd row seat 40 track EZ entry actuator to the
bracket, and then remove the actuator from the vehicle.
Tip: Use of the following tool(s) is recommended:
- Flat head screwdriver
Install
-
Position the 2nd row seat 40 track EZ entry actuator on the vehicle, and then install
the tabs (x3) that attach the actuator to the bracket.
-
Install the screws (x3) that attach the 2nd row seat 40 track EZ entry actuator to
the bracket.NoteAlign the screws with the actuator bracket.Tip: Use of the following tool(s) is recommended:
- Flex head ratchet/flex head torque wrench
- Ratchet/torque wrench
- Torx T15 socket
-
Connect the 2nd row seat 40 track EZ entry actuator connector.
-
Position the 2nd row 40 seat actuator slider vertically on the vehicle, and then
install the cable end fitting into the slider opening.
CAUTIONDo not kink or damage the cable.NoteUse the pliers to hold the cable end fitting in place during slider installation.Tip: Use of the following tool(s) is recommended:
- Needle nose long bent pliers
-
Attach the 2nd row 40 seat actuator slider cable to the slider.
CAUTIONDo not kink or damage the cable.
-
Install the clips (x2) that attach the
2nd row 40 seat actuator slider to the seat frame.
-
Apply forward pressure to the 2nd row 40 seat actuator slider, and then install the
new metal clip on the slider.
NoteDo not deform or damage the clip.NoteUse the flat side of the plastic trim tool to aid clip installation. Verify slider operation, and ensure proper functionality.Tip: Use of the following tool(s) is recommended:
- Plastic trim tool
- Small flat head screwdriver
-
Install the clip that attaches the 2nd row 40 seat harness to the seat frame.
-
Position the 2nd row 40 seat plastic seat back on the seat, and then install the
clips (x5) and Velcro strips (x2) that attach the seat back to the seat.
NoteFold the backrest cover and attach the corners of the Velcro strips.
-
Zip the 2nd row 40 seat back upholstery on the LH and RH sides of the backrest
cover.
NoteEnsure the ends of the zippers are tucked underneath the seat upholstery. Use a pick to aid in tucking the zippers.Tip: Use of the following tool(s) is recommended:
- 6in 90 degree tip miniature soft grip pick
-
Install the J-hook that attaches the 2nd row 40 seat back upholstery to the
seat.
- Unfold the 2nd row 40 seat into original position.
-
Starting at the top, carefully install the clips (x2) that attach the 2nd row 40 seat
escutcheon to the seat.
- Close the RH falcon wing door.
- Move the RH front seat into original position.
- Raise the RH front window.
- Close the RH front door.