29/07/2022 09:43:04

Cable - Recliner - 3rd Row Seat - LH (Remove and Replace)

Correction code 13032002 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH falcon wing doors.
  2. Open the liftgate.
  3. Fold the 2nd row 40 and 60 seats downward.
  4. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  5. Remove the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  6. Remove the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
  7. Fold the LH and RH 3rd row seats downward.
  8. Remove the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
  9. Release the tabs (x4), fir tree clips (x2), and J hook that attach the lower section of the LH 3rd row seat upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the tabs inward, and then upwards to release.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  10. Disconnect the LH 3rd row seat connectors (x2), and then re-route the connectors through the lower section of the upholstery.
  11. Route the LH 3rd row seat connectors (x2) around the lower section of the upholstery, and then connect the connectors.
  12. Unfold the LH 3rd row seat to original position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Leave the headrest in folded position.
  13. Release the J-hook clip that attaches the upper half of the LH 3rd row seat upholstery to the seat.
  14. From the 3rd row, pull the inner portion of the seat cover and foam outward to gain access to the LH 3rd row seat recliner actuator.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution to not snag the J-hooks. The actuator is located on the front side of the seat back under the upholstery and cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the fold function to feed the bottom of the seat upholstery forward.
  15. Cut the zip tie that attaches the LH 3rd row seat recliner actuator cable to the seat bracket, and then remove the cable from the bracket.
    Tip: Use of the following tool(s) is recommended:
    • Diagonal cutters
  16. Release the LH 3rd row seat recliner actuator cable from the actuator pulley.
  17. Remove and discard the bolt that attaches the LH 3rd row seat retractor to the seat, and then remove the retractor from the seat to gain access to the LH 3rd row seat recliner cable eyelet.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx Plus T45 socket
  18. Bend the locking tab on the LH 3rd row seat recliner cable outer eyelet outwards, and then push the eyelet down while prying outwards to release the eyelet from the pivot.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
    • Clip pry tool
  19. Bend the locking tab on the LH 3rd row seat recliner cable inner eyelet outwards, and then push the eyelet down while prying outwards to release the eyelet from the pivot.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
    • Clip pry tool
  20. Remove the LH 3rd row seat recliner outer release cable tether from the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  21. Remove the LH 3rd row seat recliner inner release cable tether from the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  22. Remove the LH 3rd row seat recliner cable from the seat, and then remove the cable from the vehicle.

Install

  1. Position the LH 3rd row seat recliner cable on the vehicle, and then install the cable into the seat.
  2. Install the LH 3rd row seat recliner cable outer eyelet on the outer recliner pivot.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
  3. Install the LH 3rd row seat recliner cable inner eyelet on the inner recliner pivot.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
    • Clip pry tool
  4. Position the LH 3rd row seat retractor on the seat, and then install the new bolt that attaches the retractor to the seat.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx Plus T45 socket
  5. Install the LH 3rd row seat recliner outter release cable tether on the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  6. Install the LH 3rd row seat recliner inner release cable tether on the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  7. Connect the LH 3rd row seat recliner actuator cable to the actuator pulley.
  8. Position the LH 3rd row seat recliner actuator cable on the seat bracket, and then install the zip tie that attaches the cable to the bracket.
    Tip: Use of the following tool(s) is recommended:
    • Zip tie
  9. Fold the seat upholstery and cushion assembly over the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the folding function to assist with tucking the upholstery.
  10. Engage the J hook clip that attaches the upper half of LH 3rd row seat upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the seat to a workable position, start at one end of the J hook clip, and then fold the clip inwards until the other end of the upholstery is fully tucked.
  11. Disconnect the LH 3rd row seat connectors (x2), and then route the connectors through the seat upholstery.
  12. Connect the LH 3rd row seat connectors (x2).
  13. Engage the tabs (x4), fir tree clips (x2), and J hook that attach the lower section of the LH 3rd row seat upholstery to the seat.
  14. Install the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
  15. Install the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
  16. Install the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  17. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  18. Unfold the LH and RH 3rd row seats into original position.
  19. Close the liftgate.
  20. Unfold the 2nd row 40 and 60 seats into original position.
  21. Close the LH and RH falcon wing doors.