08/09/2022 16:26:22

NVH Insulator - Floor - 3rd Row (Remove and Replace)

Correction code 15308302 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Open the LH and RH falcon wing doors.
  4. Move the LH and RH front seats forward.
  5. On the touchscreen, touch Controls > Frunk Open.
  6. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. Open the liftgate.
  8. Remove the LH and RH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  9. Remove the 2nd row floor mat. See Floor Mat - 2nd Row (Remove and Replace).
  10. Remove the 2nd row front floor panel. See Floor Panel - Front - 2nd Row (6 Seat) (Remove and Replace).
  11. Remove the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (6 Seat) (Remove and Replace).
  12. Move the LH and RH monopost seats forward.
  13. Remove the LH and RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  14. Remove the LH and RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  15. Remove the LH and RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  16. Remove the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (6 Seat) (Remove and Replace).
  17. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  18. Remove the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  19. Remove the rear trunk carpet. See Carpet - Rear Trunk (7 Seat) (Remove and Replace).
  20. On the touchscreen, touch Controls > Safety & Security > Power Off.
  21. Disconnect LV power. See LV Power (Disconnect and Connect).
  22. Remove the LH and RH 3rd row tray harness. See Tray Harness - 3rd Row - LH (Remove and Replace).
  23. Remove the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  24. Remove the 3rd row seat assembly. See Seat Assembly - 3rd Row (Remove and Replace).
  25. Remove the 3rd row carpet. See Carpet - 3rd Row (Remove and Replace).
  26. Remove the 3rd row floor NVH insulator from the vehicle.

Install

  1. Install the 3rd row floor NVH insulator on the vehicle.
  2. Install the 3rd row carpet. See Carpet - 3rd Row (Remove and Replace).
  3. Install the 3rd row seat assembly. See Seat Assembly - 3rd Row (Remove and Replace).
  4. Install the 3rd row seat cushion. See Cushion - Seat - 3rd Row (Remove and Replace).
  5. Install the LH and RH 3rd row tray harness. See Tray Harness - 3rd Row - LH (Remove and Replace).
  6. Install the rear trunk carpet. See Carpet - Rear Trunk (7 Seat) (Remove and Replace).
  7. Install the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  8. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  9. Connect LV power. See LV Power (Disconnect and Connect).
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Close the hood.
  12. Install the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (6 Seat) (Remove and Replace).
  13. Install the LH and RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  14. Install the LH and RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  15. Install the LH and RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  16. Close the liftgate.
  17. Move the LH and RH monopost seats to original position.
  18. Install the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (6 Seat) (Remove and Replace).
  19. Install the 2nd row front floor panel. See Floor Panel - Front - 2nd Row (6 Seat) (Remove and Replace).
  20. Install the 2nd row floor mat. See Floor Mat - 2nd Row (Remove and Replace).
  21. Install the LH and RH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  22. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors
  23. Move the LH and RH front seats to original position.
  24. Raise the LH and RH front windows.
  25. Close the LH and RH front doors.