08/04/2024 15:06:55

Retractor - Seatbelt - 1st Row - LH (Remove and Replace)

Correction code 20054102 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-08-01: Reorganized steps and removed unnecessary steps.
  • 2023-06-19: Updated seat belt linkage release and install steps.

Remove

  1. Open the LH doors and lower the LH front window.
  2. Move the LH front seat forward.
  3. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  4. Release the LH front door seal from the B-pillar trim.
  5. Remove the LH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  6. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  7. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  8. Remove the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  9. Remove and discard the nut that attaches the LH 1st row upper seatbelt to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 17 mm deep socket
    • Ratchet/torque wrench
  10. Remove the LH 1st row seatbelt intermediate web guide. See Seatbelt Intermediate Web Guide (Remove and Replace).
  11. Disconnect the LH 1st row seatbelt retractor connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide both orange locking tabs on the sides of the connector towards the rear of the connector at the same time to release the connector.
    Tip: Use of the following tool(s) is recommended:
    • Flat head screwdriver
  12. Remove and discard the bolt that attaches the LH 1st row seatbelt retractor to the vehicle, and then remove the retractor from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • 13 mm socket
    • Ratchet/torque wrench

Install

  1. Position the LH 1st row seatbelt retractor on the vehicle, and then install a new bolt that attaches the retractor to the vehicle.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    When the retractor is removed from the vehicle, the seatbelt webbing will only extend if the retractor is in as-installed orientation.
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  2. Connect the LH 1st row seatbelt retractor connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the connectors are seated properly and secure.
  3. Install the LH 1st row seatbelt intermediate web guide. See Seatbelt Intermediate Web Guide (Remove and Replace).
  4. Install a new nut that attaches the LH 1st row upper seatbelt to the vehicle.
    25 Nm (18.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 17 mm deep socket
    • Ratchet/torque wrench
  5. Install the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  6. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  7. Install the LH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  8. Fully seat the LH front door seal on the B-pillar trim.
  9. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  10. Move the LH front seat to original position.
  11. Close the LH falcon wing door.
  12. Raise the LH front window.
  13. Close the LH front door.