10/11/2022 08:01:37

Cushion Sub-assembly - 2nd Row Seat - RH (5 Seat) (Remove and Replace)

Correction code 13058802 1.38 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat assembly from the vehicle. See Seat Assembly - 2nd Row - RH (5 Seat) (Remove and Replace).
  2. Fold the RH 2nd row seat back to the upright position.
  3. Remove the RH 2nd row seat recliner lever. See Lever - Recliner - 2nd Row - LH (Remove and Replace)
  4. Remove the RH 2nd row seat outboard side shield. See Side Shield - Outboard - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  5. Remove and discard the bolt that attaches the seatbelt to the RH 2nd row seat assembly.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T50 socket
  6. Disconnect the RH 2nd row seatbelt buckle electrical connector, and then release the clips (x2) that attach the harness to the seat assembly.
  7. Remove the bolt that attaches the seatbelt buckle to the RH 2nd row seat assembly, and then remove the buckle from the assembly.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T50 socket
  8. Release the J-hooks (x6) that attach the RH 2nd row seat cushion trim to the seat bracket assembly.
  9. Disconnect the RH 2nd row seat assembly heater and seat belt reminder electrical connectors (x2), and then release the clip that attaches the seat belt reminder harness to the seat assembly.
  10. Remove the RH 2nd row seat cushion sub-assembly from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the harness and tension flaps underneath the backrest.

Install

  1. Position the RH 2nd row seat cushion sub-assembly into the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the harness and tension flaps underneath the backrest.
  2. Secure the clip that attaches the seat belt reminder harness to the RH 2nd row seat assembly, and then connect the seat heater and seat belt reminder electrical connectors (x2).
  3. Secure the J-hooks (x6) that attach the RH 2nd row seat cushion trim to the seat bracket assembly.
  4. Position the seatbelt buckle onto the RH 2nd row seat assembly, and then install the bolt that attaches the buckle to the assembly.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T50 socket
  5. Secure the clips (x2) that attach the RH 2nd row seat harness to the seat assembly, and then connect the seatbelt buckle electrical connector.
  6. Install and new bolt that attaches the seatbelt to the RH 2nd row seat assembly.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T50 socket
  7. Install the RH 2nd row seat outboard side shield. See Side Shield - Outboard - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  8. Install the RH 2nd row recliner lever. See Lever - Recliner - 2nd Row - LH (Remove and Replace).
  9. Fold the RH 2nd row seat back to the down position.
  10. Install the RH 2nd row seat assembly into the vehicle. See Seat Assembly - 2nd Row - RH (5 Seat) (Remove and Replace).