15/08/2023 10:16:04

Applique - Spine - Center (Remove and Replace)

Correction code 10403002 2.16 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.

Remove

  1. Remove the headliner. See Headliner (Remove and Install).
  2. Carefully disconnect the ultrasonic sensor electrical connector from the center spine applique.
  3. Remove the LH rear door trim lower garnish. See Garnish - Lower - Door Trim - Rear - LH (Remove and Replace).
  4. Remove the LH upper rear door trim panel. See Panel - Door Trim - Rear - Upper - LH (Remove & Replace).
  5. Remove the LH rear upper rear door trim bracket. See Bracket - Rear Door Trim - Upper - Rear - LH (Remove and Replace).
  6. Remove the LH front upper rear door trim bracket. See Bracket - Rear Door Trim - Upper - Front - LH (Remove and Replace).
  7. Remove the LH center rear door trim bracket. See Bracket - Rear Door Trim - Center - LH (Remove and Replace).
  8. Remove the mid rear LH door trim gap hider. See Gap Hider - Door Trim - LH - Rear - Mid (Remove and Replace).
  9. Lower the LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Note
    May need to assist the door to close.
  10. Remove the LH upper rear door glass assembly. See Door Glass Assembly - Rear - Upper - LH (Remove and Replace).
  11. Place suitable protective cover on the 2nd row seats.
  12. Enter the vehicle and close the LH rear door from inside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Access the rooftop through the upper rear door opening.
  13. Release the clips (x7) that attach the center spine applique to the body, and then remove applique from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Starting from the front, use a hydroblade to cut through and work around the center spine applique.
    Informational PurposesAn informational icon, calling your attention
    Note
    Separate the urethane from the applique; partially lift the LH side of the applique to gain access to the RH side.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use glass cleaner to lubricate the blade.
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully release the clips from the center spine applique, but do not damage the seal on the RH upper glass.

Install

  1. Remove excess urethane from the roof and the center spine applique carrier to prepare for installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean roof surface area with IPA wipes. Allow 1 minute for dry time before continuing.
  2. Open the LH rear door.
  3. Apply primer onto the roof and the center spine applique carrier following the urethane path.
  4. Apply primer onto the center spine applique following the urethane path.
  5. Prepare the caulking gun and urethane.
    Informational PurposesAn informational icon, calling your attention
    Note
    Opening must be 8 mm wide and 14 mm tall.
  6. Apply urethane to the center spine applique following the primer patch.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fill any gaps with urethane to ensure consistent bead.
  7. Enter the vehicle and close the LH rear door from the inside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Access to the rooftop through the upper rear door opening.
  8. With an assistant, install the center spine applique.
    Informational PurposesAn informational icon, calling your attention
    Note
    x7 clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the center spine applique onto the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect the ultrasonic sensor electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Press down firmly and ensure all the clips are fully engaged.
  9. Open the LH rear door partially.
  10. Install the LH upper rear door glass assembly. See Door Glass Assembly - Rear - Upper - LH (Remove and Replace).
  11. Install the mid rear LH door trim gap hider. See Gap Hider - Door Trim - LH - Rear - Mid (Remove and Replace).
  12. Install the LH center rear door trim bracket. See Bracket - Rear Door Trim - Center - LH (Remove and Replace).
  13. Install the LH front upper rear door trim bracket. See Bracket - Rear Door Trim - Upper - Front - LH (Remove and Replace).
  14. Install the LH rear upper rear door trim bracket. See Bracket - Rear Door Trim - Upper - Rear - LH (Remove and Replace).
  15. Install the LH upper rear door trim panel. See Panel - Door Trim - Rear - Upper - LH (Remove & Replace).
  16. Install the LH rear door trim lower garnish. See Garnish - Lower - Door Trim - Rear - LH (Remove and Replace).
  17. Install the headliner. See Headliner (Remove and Install).
  18. Verify that the Bluetooth, Wi-Fi, and LTE are functioning properly.