Switch - Recliner - 3rd Row Seat - LH (Remove and Replace)
Correction code 13032402 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Open the LH and RH falcon wing doors.
- Open the liftgate.
- Fold the 2nd row 40 and 60 seats downward.
- Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
- Remove the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
- Remove the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
- Fold the LH and RH 3rd row seats downward.
- Remove the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
-
Release the tabs (x4), fir tree clips (x2), and J hook that attach the lower section
of the LH 3rd row seat upholstery to the seat.
NotePull the tabs inward, and then upwards to release.NoteUse of the following tool(s) is recommended:
- Clip pry tool
-
Unfold the LH 3rd row seat to original position.
NoteLeave the seat headrest in the folded position.
-
Release the J-hook clip that attaches
the upper half of the LH 3rd row seat upholstery to the seat.
-
From the 3rd row, pull the top outer portion of the seat cover and foam outward to
gain access to the LH 3rd row seat escutcheon.
-
Carefully pull the LH 3rd row seat escutcheon forward to access the LH 3rd row seat
recliner switch connector, and then disconnect the switch connector.
-
Remove the screws (x2) that attach the LH 3rd row seat recliner switch to the seat,
and then remove the switch from the seat.
NoteUse of the following tool(s) is recommended:
- PH1 Phillips screwdriver
Install
-
Position the LH 3rd row seat recliner
switch on the seat, and then install the screws that attach the switch to the seat.NoteUse of the following tool(s) is recommended:
- PH1 Phillips screwdriver
-
Connect the LH 3rd row seat recliner
switch connector, and then install the seat escutcheon into the seat back cushion
trim.
-
From the 3rd row, fold the top outer
portion of the LH 3rd row seat cover and foam back over the seat frame.
-
Engage the J hook clip that attaches
the upper half of LH 3rd row seat upholstery to the seat.
NoteFold the seat to a workable position, start at one end of the J hook clip, and then fold the clip inwards until the other end of the upholstery is fully tucked.
-
Engage the tabs (x4), fir tree clips (x2), and J hook that attach the lower section
of the LH 3rd row seat upholstery to the seat.
- Install the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
- Install the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
- Install the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
- Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
- Unfold the LH and RH 3rd row seats into original position.
- Close the liftgate.
- Unfold the 2nd row 40 and 60 seats into original position.
- Close the LH and RH falcon wing doors.