29/07/2022 15:11:31

Slider - Actuator - 2nd Row (5/7 Seat) (Remove and Replace)

Correction code 13028302 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the RH front door.
  2. Lower the RH front window.
  3. Move the RH front seat forward.
  4. Open the RH falcon wing door.
  5. Starting from the bottom, carefully pry the 2nd row seat escutcheon away from the seat back to release the clips (x2), and then release the escutcheon from the seat.
  6. Fold the 2nd row 40 seat downwards.
  7. Release the J-hook that attaches the 2nd row 40 seat back upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the backrest upholstery down upon release.
    Tip: Use of the following tool(s) is recommended:
    • 6in 90 degree tip miniature soft grip pick
  8. Unzip the 2nd row 40 seat back upholstery on the LH and RH sides of the backrest cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ends of the zippers are tucked underneath the seat upholstery. Use a pick to aid in moving the zippers.
    Tip: Use of the following tool(s) is recommended:
    • 6in 90 degree tip miniature soft grip pick
  9. Release the clips (x5) and Velcro strips (x2) that attach the 2nd row plastic seat back to the seat assembly, and then remove the plastic seat back from the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the backrest cover over the headrest for access.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  10. Release the clip that attaches the seat harness to the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  11. Relieve the tension on the metal clip by moving the 2nd row actuator slider into the housing, and then remove and discard the metal clip from the actuator slider.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
    • Small flat head screwdriver
  12. Release the cable from the 2nd row actuator slider.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution not to damage the cable locating plastic.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  13. Release the clips (x2) that attach the 2nd row actuator slider on the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Clip pry tool
  14. Move the 2nd row actuator slider towards the cable to relieve tension.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
  15. Flip the 2nd row actuator slider vertically, use a pick to release the cable end fitting from the open slot, and then remove the slider from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick

Install

  1. Position the 2nd row actuator slider vertically on the vehicle, and then install the cable end fitting into the slider opening.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the pliers to hold the cable end fitting in place during slider installation.
    Tip: Use of the following tool(s) is recommended:
    • Needle nose long bent pliers
  2. Attach the 2nd row actuator slider cable to the slider.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
  3. Install the clips (x2) that attach the 2nd row actuator slider to the seat frame.
  4. Apply forward pressure to the 2nd row actuator slider, and then install the new metal clip on the slider.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not deform or damage the clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the flat side of the plastic trim tool to aid clip installation. Verify slider operation, ensure proper functionality.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
    • Small flat head screwdriver
  5. Install the clip that attaches the seat harness to the seat frame.
  6. Position the 2nd row plastic seat back on the seat assembly, and then install the clips (x5) and Velcro strips (x2) that attach the seat back to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the backrest cover and attach the corners of the Velcro strips.
  7. Zip the 2nd row 40 seat back upholstery on the LH and RH sides of the backrest cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the ends of the zippers are tucked underneath the seat upholstery. Use a pick to aid in tucking the zippers.
    Tip: Use of the following tool(s) is recommended:
    • 6in 90 degree tip miniature soft grip pick
  8. Install the J-hook that attaches the 2nd row 40 seat back upholstery to the seat.
  9. Unfold the 2nd row 40 seat into original position.
  10. Starting at the top, carefully install the clips (x2) that attach the 2nd row escutcheon to the seat.
  11. Close the RH falcon wing door.
  12. Move the RH front seat into original position.
  13. Raise the RH front window.
  14. Close the RH front door.