Current Release Notes

Archived Release Notes:

Week Ending December 21, 2024

The following procedure(s) were updated:
  1. Glare Shield - Autopilot (Remove and Replace) - Added images with HW4 GNSS antenna.
  2. Heater - Radar (Rework) (Vehicles Built Before July 1, 2021) - Updated title and procedure details.
  3. Heater - Radar (Rework) (Vehicles Built After July 1, 2021) - Updated title and procedure details.
  4. Sensor - Radar - Front (Remove and Replace) - Obsoleted the procedure.

Week Ending December 14, 2024

The following new procedure(s) were added:
  1. New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. The Pre-Installation Glass Inspection procedure explains how to inspect new windshield, roof, door, and fixed glass components before the new component is installed.
The following procedure(s) were updated:
  1. Added a new caution about Pre-Installation Glass Inspection service requirements:
  2. Four Wheel Alignment Check and Adjust - Removed instruction to add the test drive correction code. The test drive is now included in the alignment FRT.
  3. Frame - Seat Cushion - Driver Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  4. Latch - Seat Back - 2nd Row Seat - LH (Remove and Replace) - Updated the seat back latch-to-seat assembly bolts torque spec to 40 Nm.
  5. Motor - Seat Tilt - Driver Seat (Remove and Replace) - Added mini-tilt motor configuration information.

Week Ending December 7, 2024

The following procedure(s) were updated:
  1. Updated inverter fastener torque sequence.
  2. Seat Assembly - 1st Row - LH (Remove and Replace) - Added configuration information for seat assemblies with the mini-tilt motor.
  3. Seat Assembly - 1st Row - RH (Remove and Replace) - Added configuration information for seat assemblies with the mini-tilt motor.
  4. Sensor - HVAC - Windshield (Remove and Replace) - Updated notes and Service Mode instructions.
  5. Steering Column (Remove and Replace) - Updated steering column configuration and calibration steps.
  6. TPMS (Sensor ID Drive Learn) - Updated Service Mode instructions.
  7. TPMS (Sensor ID Tool Learn) - Updated Service Mode instructions.

Week Ending November 30, 2024

The following procedure(s) were updated:
  1. Steering Yoke/Wheel (Remove and Replace) - Updated the tools used to remove/install the bolt that attaches the steering yoke/wheel to the steering column.

Week Ending November 23, 2024

The following procedure(s) were updated:
  1. Battery - LV (Remove and Replace) - Added a note to remind of checking the 12V/LV battery temperature before performing the procedure.

Week Ending November 16, 2024

The following procedure(s) were updated:
  1. Antenna - GNSS (Remove and Replace) - Updated images of the HW4 antenna.

Week Ending November 9, 2024

The following new procedure(s) were added:
  1. Windshield Chip Repair (EMEA)
The following procedure(s) were updated:
  1. Camera - Interior (Remove and Replace) - Added note that Service Mode must be enabled prior to connecting the replacement camera.
  2. HV Battery (AWD) (Remove and Replace) - Updated HV battery discharge steps.
  3. Steering Yoke/Wheel (Remove and Replace) - Added extra configuration instructions.

Week Ending October 26, 2024

The following procedure(s) were updated:
  1. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a video demonstrating precision cleaning of windshield.
  2. Hydraulic Control Unit (HCU) - Brake (Remove and Replace) - Added steps to run Service CAN Redeploy.
  3. Link - Aft - Lower - Rear - LH (Remove and Replace) - Deleted steps for ride height measurement.
  4. Link - Aft - Upper - Rear - LH (Remove and Replace) - Deleted steps for ride height measurement.

Week Ending October 19, 2024

The following procedure(s) were updated:
  1. Car Computer (Remove and Replace) - Added instruction for car computer disposal.
  2. Decor - Trim - Rear Door - LH (Remove and Replace) - Updated décor images and clip quantity to align with latest validation.
  3. Four Wheel Alignment Check - Updated tire inflation instructions.

Week Ending October 12, 2024

The following new procedure(s) were added:
  1. Event Data Recorder Retrieval
The following procedure(s) were updated:
  1. Fender Garnish and Wheel Fairing Assembly - Front - LH (Remove and Replace) - Removed front liner cover, Jack Mode, and suspension height adjustment steps.
  2. Inverter - Front Drive Unit (Remove and Replace) - Updated the clevis mount to isolator mount torque spec.

Week Ending October 5, 2024

The following procedure(s) were updated:
  1. Applique - Roof - Rear (Remove and Replace) - Added urethane thickness spec.