20/08/2024 09:58:07

LV Battery - Recover

Correction code 17010008 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Disconnect LV battery connector and keep FRL connected
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Keep FRL connected
  3. Connect 12V maintainer while LV battery is connected and cycle contactors on
    Informational PurposesAn informational icon, calling your attention
    Note
    1x tab, Connect 12V support while LV battery is connected, Release jump post cover behind wiper module, Place rag between multisystem beam and jump post, Prevent shorting positive cable to ground, Route positive clamp between brake fluid reservoir and wiper module, Secure positive terminal to jump post, Secure negative terminal to multisystem beam, Connect maintainer to power supply, Contactors will turn on and there will be an audible click
  4. Secure LV battery connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Seat LV battery connection and push black connector lock inwards to secure, Engage upper locking tab when fully seated
  5. Open the LH front door.
  6. Lower both front windows.
  7. Activate Service Mode using the touchscreen.
  8. Remove 12V maintainer
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove 12V support after firmware is completed, Unplug maintainer first and then remove from posts, Return cap to positive post
  9. Navigate to Power Distribution
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Service UI select Low Voltage > Power Distribution
  10. Verify the status of the LV battery.
    Informational PurposesAn informational icon, calling your attention
    Note
    If after 2 minutes of PCS support, alerts VCLEFT_a478_LVBMS_MOSFET_Open or VCBATT_a478_LVBMS_MOSFET_Open are present, the LV battery has not auto-recovered. Auto-recovery can be manually attempted via touchscreen or Toolbox:
    • Touchscreen:Service Mode > Low Voltage > Power Distribution > Close MOSFET
    • Toolbox: Run the ActionPROC_VCFRONT_X_RECONNECT-LV-BATTERYvia Toolbox: (link)via Service Mode: Low Voltage ➜ Power Distribution ➜ Close MOSFET
    Informational PurposesAn informational icon, calling your attention
    Note
    If the steps above do not succeed in auto-recovering the LV battery, recover the battery using the Tesla Li-Ion battery charger (STILL IN DEVELOPMENT).
    • Verify that the battery is not discharging at high current and is not self-protecting.
    • Go to Service Mode > Low Voltage > Power Distribution > LV Battery and confirm that LV battery SoC is increasing.
    • Verify that the LV Battery MOSFET status is Closed.
  11. Exit Service mode
    Informational PurposesAn informational icon, calling your attention
    Note
    Press and hold the Exit Service Mode button for 3 seconds
  12. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).