Release Notes October-December 2023

Archived Release Notes:

Week Ending December 30, 2023

The following new procedure(s) were added:
The following procedure(s) were updated:
  1. Valance - Front Fascia (Remove and Replace) - Added steps of removing and installing the LH and RH fender garnishes.

Week Ending December 23, 2023

The following new procedure(s) were added:
  1. Door Assembly - Charge Port (Global) (Remove and Replace)
  2. Sump Seal - HVAC Assembly \(Remove and Replace\)
The following procedure(s) were updated:
  1. Brake Fluid Bleed/Flush (Remove and Replace) - Updated brake stiffness routine.
  2. Camera - Interior (Remove and Replace) - Fixed errors.

Week Ending December 16, 2023

The following procedure(s) were updated:
  1. Door Glass - Front - LH (Adjust) - Updated the original nonadjustable correction code to the new adjustable one.

Week Ending December 8, 2023

The following new procedure(s) were added:
  1. Ultrasonic Sensor Holder - Butyl - Rear Door – LH (Remove and Replace)
The following procedure(s) were updated:
  1. Four Wheel Alignment Check and Adjust - Revised procedure to be in line with latest PDS validation.
  2. Ride Height (Adjust) - Revised procedure to be in line with latest PDS validation.

Week Ending December 1, 2023

The following procedure(s) were updated:
  1. Fascia Assembly - Front (HW4) (Remove and Replace) - Reorganized the procedure.

Week Ending November 25, 2023

The following new procedure(s) were added:
The following procedure(s) were updated:
  1. Brake Rotor - Rear - LH (Remove and Replace) - Added extra information for single rotor replacement.
  2. Brake Rotor - Front - LH (Remove and Replace)- Added extra information for single rotor replacement.
  3. Harness - Main Front (Remove and Replace) - Added installation step to attach the AP power supply cable to the ground point.
  4. Insulator - Top Cowl (Remove and Replace) - Reorganized the procedure.
  5. Module - Body Controller - Security (Remove and Replace) - Updated security controller configuration steps.
  6. Module - Steering Column Control (Remove and Replace) - Replaced Toolbox routine PROC-VCLEFT_X_STEERING-COLUMN-CALIBRATIONvia Toolbox: (link) with PROC_STEERING_COLUMN_CALIBRATIONvia Toolbox: (link)via Service Mode: Chassis ➜ Steering ➜ Calibrate Steering Column.
  7. Tire Rotation - Added step to reset learned tire values.

Week Ending November 18, 2023

The following procedure(s) were updated:
  1. Module - Body Controller - LH (Remove and Replace) - Updated post-replacement routine.
  2. Module - Body Controller - RH (Remove and Replace) - Updated post-replacement routine.
  3. Pump - Coolant - Battery - Offboard (Remove and Replace) - Reorganized the procedure.
  4. Pump - Coolant - Powertrain - Radiator (Remove and Replace) - Reorganized the procedure.

Week Ending November 11, 2023

The following procedure(s) were updated:
  1. HV Battery (AWD) (Remove and Replace) - Updated UI steps.
  2. Hose - Offboard Powertrain Pump To Radiator (Remove and Replace) - Reorganized the procedure.
  3. Hose - Powertrain Supply - HV Battery to Supermanifold (Remove and Replace) - Reorganized the procedure.
  4. Steering Yoke/Wheel (Remove and Replace) - Added a note to install the correct airbag variant.

Week Ending November 4, 2023

The following procedure(s) were updated:
  1. A/C Compressor (Remove and Replace) - Reorganized the procedure.
  2. A/C Refrigerant (Recovery and Recharge) - Reorganized the procedure.
  3. Battery - LV (Remove and Replace) - Replaced Toolbox 3 CAN redeploy with Service Mode UI software reinstall.
  4. Bracket - Compressor (Remove and Replace) - Reorganized the procedure.
  5. Brake Caliper - Rear - LH (Remove and Replace) - Update the torque of rear brake caliper to the knuckle.
  6. Hose - Outlet - Radiator (Remove and Replace) - Reorganized the procedure.
  7. Hose - Radiator to 3 Way Valve (Remove and Replace) - Reorganized the procedure.
  8. Shroud - Cooling Fan Module (Remove and Replace) - Reorganized the procedure.
  9. Subframe Assembly - Rear (Remove and Install) - Added steps for dummy plug on HV battery RH HV header.

Week Ending October 28, 2023

The following new procedure(s) were added:
  1. Gateway Configuration (Display and Change)
The following procedure(s) were updated:
  1. Knuckle - Suspension - Rear - LH (Remove and Replace) - Updated EPB Service Mode reference.
  2. Module - Body Controller - Security (Remove and Replace) - Updated post-replacement Toolbox routines.
  3. Park Brake Caliper - Release - Updated with new Toolbox routines.
  4. Seal - Axle - Rear Drive Unit - LH (Remove and Replace) - Updated EPB Service Mode reference.
  5. Seal - Axle - Rear Drive Unit - LH (Plaid) (Remove and Replace) - Updated EPB Service Mode reference.
  6. Seat Assembly - 1st Row - LH (Remove and Replace) - Updated gateway configuration value to be set when replacing a seat not equipped with a Farside Air Bag by a seat equipped with a Farside Air Bag, replaced Toolbox routines by touchscreen routines.
  7. Steering Yoke/Wheel (Remove and Replace) - Added a warning.
  8. TPMS (Sensor ID Tool Learn) - Updated procedure and Toolbox routine.

Week Ending October 21, 2023

The following new procedure(s) were added:
  1. SIM Card - Car Computer (Remove & Replace)
  2. Duct - Center Console - 3rd Row (Remove and Replace)
The following procedure(s) were updated:
  1. Brake Caliper - Rear - LH (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.
  2. Brake Pads and Rotors - Rear - Set (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.
  3. Brake Pads - Rear (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.
  4. Brake Rotor - Rear - LH (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.

Week Ending October 14, 2023

The following new procedure(s) were added:
  1. AC Cable - Charge Port to HV Battery (3-Phase) (Remove and Replace)

Week Ending October 7, 2023

The following procedure(s) were updated:
  1. Oil Pump - LH - Rear Drive Unit (Plaid) (Manual Drain) (Remove and Replace) - Corrected EDF2 gearbox fluid.
  2. Touchscreen (HW3) (Remove and Replace) - Added step for checking vehicle firmware version.