Release Notes October-December 2022
Archived Release
Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending December 24, 2022
The following new procedure(s) were added:
Week Ending December 17, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Contactor - Fast Charge - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Contactor - Negative - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Contactor - Positive - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Controller - High Voltage (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Cover - Front Access - HV Battery (Remove and Install) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Cover - Rear Access - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Harness - Pyrotechnic - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Power Conversion System (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- Shunt - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
- A/C Refrigerant (Recovery and Recharge) - Added information on manual oil injection.
Week Ending December 10, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Seat Assembly - 1st Row - LH (Remove and Install) - Updated references from Driver to 1st row LH.
- Seat Assembly - 1st Row - LH (Remove and Replace) - Updated references from Driver to 1st row LH.
- Seat Assembly - 1st Row - RH (Remove and Install) - Updated references from Front Passenger to 1st row RH.
- Seat Assembly - 1st Row - RH (Remove and Replace) - Updated references from Front Passenger to 1st row RH.
Week Ending November 26, 2022
The following new procedure(s) were added:
Week Ending November 19, 2022
The following new procedure(s) were added:
- Cooling System (Check and Fill) - This procedure decribes coolant top off without system air purge.
- Pad - Lifting - Each (Remove and Replace)
The following procedure(s) were updated:
- Cooling System (Partial Refill and Bleed) - Updated procedure title. This procedure describes coolant top off and system air purge.
- Firmware Update - Updated steps per latest prompts on the vehicle touchscreen.
Week Ending November 12, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Sensor - Radar - Front (Calibration) - Updated procedure to perform alignment check only drifting/pulling noticed during the test drive.
- Sensor - Radar - Front (Remove and Replace) - Updated procedure to perform alignment check only drifting/pulling noticed during the test drive.
- Windshield (Remove and Install) - Added a Caution and image to show two locations to be extra cautious when cutting urethane.
- Windshield (Remove and Replace) - Added a Caution and image to show two locations to be extra cautious when cutting urethane.
- Windshield (Reuse Humidity and Temperature Sensor) (Remove and Replace) - Added a Caution and image to show two locations to be extra cautious when cutting urethane.
Week Ending November 5, 2022
The following procedure(s) were updated:
- Carrier - Connector - Front - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Contactor - Fast Charge - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Contactor - Negative - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Contactor - Positive - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Controller - High Voltage (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Cover - Front Access - HV Battery (Remove and Install) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Cover - Rear Access - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Harness - A/C Compressor HV Header - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Harness - High Voltage Controller - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Harness - LV - Front - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Harness - Pyrotechnic - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- HV Harness - Power Conversion System (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Power Conversion System (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
- Shunt - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
Week Ending October 22, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Pyrotechnic Battery Disconnect (Remove and Replace) - Added steps to balance the voltage across the pyrotechnic battery disconnect mount points.
Week Ending October 8, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Controller - High Voltage (Remove and Replace) - Added links to backup and restore procedures.
- Four Wheel Alignment Check and Adjust - Revised procedure; suspension set to “low” and revised Toolbox settings
- Remove Stuck Deadfront - Charge Handle - Added first step to de-energize the Wall Connector or UMC, and step to put on PPE.
- Ride Height (Adjust) - Revised entire topic
- Wheel Alignment - Chassis Height: Revised specification; also suspension ride height set to “low”