Week Ending September 30, 2023

The following procedure(s) were updated:

1. Harness - Instrument Panel (Remove and Replace) - Corrected links for touchscreen removal in Remove and Install section.
2. Module - Steering Column Control (Remove and Replace) - Updated steps per latest time study. The upper steering column shroud, steering column gap hider, and other IP trims no longer need to be removed.
3. Seal - Door - Charge Port (Retrofit) - Added additional info for the application of the CKL charging identifier label (Europe) and the High Voltage warning label (China).

Week Ending September 23, 2023

The following new procedure(s) were added:

1. Fuse Locations

The following procedure(s) were updated:

1. ECU - Charge Port (Remove and Replace) - Optimized the whole procedure in a more efficient way.

Week Ending September 16, 2023

The following new procedure(s) were added:

1. Seal - Door - Charge Port (Retrofit)

The following procedure(s) were updated:

1. Firmware Reinstall - Touchscreen - Updated to one procedure that can be performed regardless of contactor state.
2. Panel Alignment Specifications - Redirected the information on panel alignment specifications to a new location.

Week Ending September 2, 2023

The following new procedure(s) were added:

1. Charge Port Voltage Check
2. Panel Alignment Specifications

The following procedure(s) were updated:

1. Brake Caliper - Rear - LH (Remove and Replace) - Updated caliper to knuckle torque spec.
2. Busbars - Charge Port to HV Battery (EMEA) (Remove and Replace) - Added link to charge port voltage check procedure.
3. Busbars - Charge Port to HV Battery (Remove and Replace) - Added link to charge port voltage check procedure.
4. Charge Port (EMEA) (Remove and Replace) - Added link to charge port voltage check procedure.
5. Charge Port (Remove and Replace) - Added link to charge port voltage check procedure.
6. Door - Charge Port (Global) (Adjust) - Added link to charge port voltage check procedure.
7. Module - Steering Column Control (Remove and Replace) - Added part number for the harness retaining clip.
8. Safety Cap - Busbar - Charge Port to HV Battery (Remove and Replace) - Added link to charge port voltage check procedure.

Week Ending August 26, 2023

The following procedure(s) were updated:

1. Module - Restraint Control (Remove and Replace) - Added additional warning to make sure LV is disconnected.

Week Ending August 19, 2023

The following new procedure(s) were added:

1. Clean And Lubricate Brake Calipers (Integrated Parking Brake)

The following procedure(s) were updated:

1. All procedures in which chemicals containing diisocyanates are used: added a note on training and certification (EMEA only)
2. Raise Vehicle - 2 Post Lift - Added to set air suspension to "Very High" before Jack Mode is enabled.
3. Raise Vehicle - Floor Jack (Mobile Service) - Added to set air suspension to "Very High" before Jack Mode is enabled.
4. Tire Rotation - Added a note about mobile correction codes.
5. Line - Air Suspension (Repair) - Add tool number.

Week Ending August 12, 2023

The following procedure(s) were updated:

1. Camera - Forward Facing (Pitch Verification) - Updated the procedure.
2. Glass - Rear Quarter - LH (Remove and Install) - Added step to cut triangle into urethane applicator tip.
3. Glass - Rear Quarter - LH (Remove and Replace) - Added step to cut triangle into urethane applicator tip.
4. Windshield (Remove and Install) - Added reference to camera pitch verification procedure.
5. Windshield (Remove and Replace) - Added reference to camera pitch verification procedure.

Week Ending August 5, 2023

The following new procedure(s) were added:

1. Line - Air Suspension (Repair)
2. Oil Pump - LH - Rear Drive Unit (Plaid) (Remove and Replace)

The following procedure(s) were updated:

1. Controller - High Voltage (Backup and Restore) - Removed Autodiag method.
2. Drive Unit - Front (Remove and Install) - Added steps to disconnect frunk harness from front drive unit connector and remove ground strap.
3. Drive Unit - Front (Remove and Replace) - Added steps to disconnect frunk harness from front drive unit connector and remove ground strap.
4. Gearbox Fluid - Front Drive Unit (Drain and Refill) - Updated procedure to latest GSD validation of July 3rd, 2023.
5. Harness - High Voltage Controller - HV Battery (Remove and Replace) - Updated harness to pack enclosure bolt torque.
6. Harness - LV - Front - HV Battery (Remove and Replace) - Updated LV DC header bolts torque.
7. HV Battery (AWD) (Remove and Install) - Added notes, cautions, and warnings for releasing and installing charge port busbar connector.
8. HV Battery (AWD) (Remove and Replace) - Added notes, cautions, and warnings for releasing and installing charge port busbar connector.
9. Inverter - Front Drive Unit (Remove and Replace) - Added steps to remove and install NVH cover.
10. Mount - Bushing Carrier - Front Drive Unit - RH (Remove and Replace) - Added steps to disconnect frunk harness from front drive unit connector and remove ground strap.
11. Retractor - Seatbelt - 1st Row - LH (Remove and Replace) - Reorganized steps and removed unnecessary steps.
12. Service Mode (Enable and Disable) - Added video.

Week Ending July 29, 2023

The following new procedure(s) were added:

1. Actuator - Pedestrian Protection - LH (EMEA) (Remove and Replace)
2. Switch - Hazard Warning (Remove and Replace)

The following procedure(s) were updated:

1. Inverter - Front Drive Unit (Remove and Replace) - Updated resolver error learn step.
2. Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Removed steps that detail the resolver error learn.
3. Inverter - Rear Drive Unit (Remove and Replace) - Removed steps that detail the resolver error learn.
4. Module - Body Controller - Security (Remove and Replace) - Added Note about security-related toolbox actions.
5. Pyrotechnic Battery Disconnect (Remove and Replace) - Added step to record replacement pyrotechnic battery disconnect serial number and part number for later entry into SCA.
6. Replacement Keys - Program (No Keys Present) - Added Note about security-related toolbox actions.

Week Ending July 22, 2023

The following procedure(s) were updated:

1. Camera - Forward Facing (Pitch Verification) - Added steps to set the ride height and enable Jack Mode.
2. Four Wheel Alignment Check and Adjust - Added Service Mode instructions.
3. Gearbox Fluid - Front Drive Unit (Drain and Refill) - Reorganized the procedure.
4. Safety Cap - Busbar - Charge Port to HV Battery (Remove and Replace) - Reorganized the procedure.

Week Ending July 15, 2023

The following new procedure(s) were added:

The following procedure(s) were updated:

1. Air Suspension - Pressurize / Depressurize - Full System - Updated procedure using Service Mode.
2. Airbag - Driver (Remove and Replace) - Added warning and repaired broken link.
3. Brake Caliper - Front - LH (Remove and Replace) - Added note w/ image for anti-rattle clip position clarification.
4. Filter - HEPA (Remove and Replace) - Reorganized the procedure.

Week Ending July 8, 2023

The following procedure(s) were updated:

1. Harness - Main Front (Remove and Replace) - Added steps to remove/install the accelerator pedal.
2. Steering Yoke/Wheel (Remove and Replace) - Updated tool.