Release Notes April-June 2024

Archived Release Notes:

Week Ending June 29, 2024

The following procedure(s) were updated:
  1. Drive Unit - Front (Remove and Install) - Added special tool list to procedure.
  2. Drive Unit - Front (Remove and Replace) - Added special tool list to procedure.

Week Ending June 22, 2024

The following new procedure(s) were added:
  1. Window Regulator (Recalibrate)
The following procedure(s) were updated:
  1. Check Valve - Liquid Cooled Condenser (Remove and Replace) - Added step to make sure that the A/C system is depressurized before removing the cooled condenser check valve and added running ODIN routines through the touchscreen.

Week Ending June 15, 2024

The following procedure(s) were updated:
  1. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Updated the inspection method and diagrams and added the tool list.
  2. Headlights - Adjust (Global) (Tool Method) - Updated procedure to latest validation.
  3. Headlights - Adjust (Global) (Wall Method) - Completely revised procedure.
  4. Vehicle HV Disablement Procedure - Added steps to set suspension height and activate Jack Mode before step that instructs to disconnect LV.

Week Ending June 8, 2024

The following procedure(s) were updated:
  1. Firmware Update - Mobile Connector - Added steps to update Mobile Connector firmware on vehicles operating software version 2024.14+.
  2. Halfshaft - Rear Drive Unit - LH (Remove and Replace) - Updated EPB Service Mode reference.
  3. Knuckle - Suspension - Rear - LH (Remove and Replace) - Updated EPB Service Mode reference.
  4. Park Brake Caliper - Release - Added procedure using Service Mode.
  5. Seal - Axle - Rear Drive Unit - LH (Plaid) (Remove and Replace) - Updated EPB Service Mode reference.
  6. Seal - Axle - Rear Drive Unit - LH (Remove and Replace) - Updated EPB Service Mode reference.
  7. Vehicle HV Disablement Procedure - Added warning to measure the specified order of locations for high voltage.

Week Ending June 1, 2024

The following procedure(s) were updated:
  1. Raise Vehicle - 2 Post Lift - Added EMEA specific info on offsetting lift pads to provide additional clearance for HV battery removal.

Week Ending May 25, 2024

The following new procedure(s) were added:
  1. Rocket Clip - Seat Cushion - 3rd Row - LH (Remove & Replace)
The following procedure(s) were updated:
  1. Fairing - Wheel - Front - LH (Remove & Install) - Changed procedure from Remove and Replace to Remove and Install, since the front wheel fairing is no longer separately serviceable.
  2. Fender Garnish and Wheel Fairing Assembly - Front - LH (Remove and Replace) - Updated procedure to service the "fender garnish and wheel fairing assembly".
  3. Updated all "Vehicle Electrical Isolation Procedure" references to "Vehicle HV Disablement Procedure".

Week Ending May 18, 2024

The following new procedure(s) were added:
  1. EPAS Grounding Points - Front Rails (Restore)
The following procedure(s) were updated:
  1. Desiccant (Remove and Replace) - Updated accumulator cap removal step so that the cap is removed with a slide hammer and female-to-female threaded adapter.
  2. Module - Restraint Control (Remove and Replace) - Replaced Toolbox 3 routines by routines using the touchscreen.
  3. Service Mode Plus - Added Service Mode Plus activation using the Vehicle Ops App.
  4. Subframe Assembly - Rear (Remove and Install) - Added subframe jig PN.

Week Ending May 11, 2024

The following procedure(s) were updated:
  1. Bracket - License Plate - Front (Rework) - Added the license plate removal and installation steps.
  2. Sensor - Radar - Front (Calibration) - Added extra info that procedure is not required if no radar is present.

Week Ending May 4, 2024

The following new procedure(s) were added:
  1. Tire - Front - LH (Repair)
The following procedure(s) were updated:
  1. Tire Rotation - Updated instructions on how to reset tire rotation through the vehicle touchscreen, and removed the Toolbox 3 method.

Week Ending April 27, 2024

The following procedure(s) were updated:
  1. Cladding - Door - Front - LH (Remove & Replace) - Added step to wet out new cladding with a silicone roller.
  2. Pump - Coolant - Powertrain - Supermanifold (Remove and Replace) - Removed the thermal test steps and updated the way of performing the routines from using Toolbox to using the touchscreen.
  3. Pump - Coolant - Battery - Supermanifold (Remove and Replace) - Removed the thermal test steps and updated the way of performing the routines from using Toolbox to using the touchscreen.
  4. Vehicle HV Disablement Procedure - Updated the order of measuring the voltage at each terminal to ground first before measuring the voltage at both terminals.

Week Ending April 20, 2024

The following new procedure(s) were added:
  1. Busbars - Charge Port to HV Battery (GB) (Remove & Replace)

Week Ending April 13, 2024

The following procedure(s) were updated:
  1. Battery - LV (Remove and Replace) - Added a Note to perform the recovery of the LV battery per Toolbox article prior to its replacement.
  2. Desiccant (Remove and Replace) - Added reminding of wearing PPEs.
  3. Fluid Capacities - Removed gearbox fluid types.
  4. Gearbox Fluid - Front Drive Unit (Drain and Refill) - Updated gearbox fluid information with link.
  5. Gearbox Fluid - Rear Drive Unit (Plaid) (Drain and Refill) - Updated gearbox fluid information with link.
  6. Inverter - Front Drive Unit (Remove and Replace) - Updated gearbox fluid information with link.
  7. Oil Pump - Front Drive Unit (Remove and Replace) - Updated gearbox fluid information with link.
  8. Windshield (Remove and Install) - Added a step of cleaning the windshield, especially the forward-facing camera area, to ensure a clear view of the forward-facing camera.

Week Ending April 6, 2024

The following new procedure(s) were added:
  1. Door Assembly - Charge Port (Global) (Remove and Replace)
The following procedure(s) were updated:
  1. Desiccant (Remove and Replace) - Added reminding of checking the pressure of A/C system before opening the accumulator.
  2. Fluids - Added new Gearbox Fluid section. - Updated washer fluid for North America.
  3. Headlights - Adjust (Global) (Wall Method) - Updated measurements and units.
  4. Headlights - Adjust - NA (Wall Method) - Updated measurements and units.