Release Notes January-March 2024
Archived Release
Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending March 30, 2024
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fluids - Updated DOT 4 BASF Hydraulan 404 as the approved brake fluid.
- Module - Steering Column Control (Remove and Replace) - Removed ODIN routines from procedure as per latest validation.
- Pedal Assembly (Remove and Replace) - Added IP carrier bolts (x2) to bulkhead torque spec.
Week Ending March 23, 2024
The following procedure(s) were updated:
- Fluids - Added compressor oil density note and leak detection kit info.
- Motor - Seat Track - Driver Seat (Remove and Replace) - Changed the steps of replacing with single seat track motor to steps of replacing with seat track motor bridge assembly.
- Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added DAS reset steps.
Week Ending March 16, 2024
The following new procedure(s) were added:
The following procedure(s) were updated:
- Link - Aft - Upper - Rear - LH (Remove and Replace) - Added a step of discarding the rotor bolt after removal and deleted the step of installing the rotor bolt.
Week Ending March 9, 2024
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fluids - Added 1646886-02-A KAF1 gearbox fluid.
- Raise Vehicle - Floor Jack (Mobile Service) - Added a warning to stay away from the vehicle before lifting to avoid injury.
- Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added detailed instructions on how to clean the windshield and added steps of camera inspection after cleaning.
Week Ending March 2, 2024
The following procedure(s) were updated:
- Tuner - FM / HD / XM (Remove and Replace) - Added Toolbox 3 steps.
- Updated the gearbox fluid to KAF1 for the following topics:
- Drive Unit - Front (Remove and Replace)
- Drive Unit - Rear (Remove and Replace)
- Drive Unit - Rear (Plaid) (Remove and Replace)
- Fluids
- Fluid Capacities
- Gearbox Fluid - Front Drive Unit (Drain and Refill)
- Gearbox Fluid - Rear Drive Unit (Drain and Refill)
- Gearbox Fluid - Rear Drive Unit (Plaid) (Drain and Refill)
- Inverter - Front Drive Unit (Remove and Replace)
- Inverter - Rear Drive Unit (Remove and Replace)
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace)
- Heat Exchanger - Front Drive Unit (Remove and Replace)
- Heat Exchanger - Rear Drive Unit (Long Range) (Remove and Replace)
- Heat Exchanger - Rear Drive Unit - LH (Plaid) (Remove and Replace)
- Oil Pump - Front Drive Unit (Remove and Replace)
- Oil Pump - Rear Drive Unit (Long Range) (Remove and Replace)
- Oil Pump - LH - Rear Drive Unit (Plaid) (Manual Drain) (Remove and Replace)
Week Ending February 10, 2024
The following procedure(s) were updated:
- Brightwork - Upper - Front - LH (Remove and Replace) - Added steps for clips securing seal and brightwork to body.
- Compressor, Supermanifold, and A/C Lines (Remove and Replace) - Cleaned up topic.
- Pedal Assembly (Remove and Replace) - Updated step to remove LH instrument panel middle trim, and not the instrument panel décor.
- Side Repeater Camera - Front - LH (HW4) (Remove and Replace) - Added a caution to wrap the terminals of the camera and wiring harness to prevent them from coming into contact with water or other solutions that could cause damage.
- Side Repeater - Front - LH (HW4) (Remove and Replace) - Added a caution to wrap the terminals of the camera and wiring harness to prevent them from coming into contact with water or other solutions that could cause damage.
- Windshield (Remove and Install) - Re-structured the procedure.
- Windshield (Remove and Replace) - Re-structured the procedure.
Week Ending February 3, 2024
The following procedure(s) were updated:
- Applique - B-Pillar - LH (Remove and Replace) - Reorganized firmware redeploy and calibration steps.
- Pyrotechnic Battery Disconnect (Remove and Replace) - Updated tools and cautions for removing and installing the pyrotechnic battery disconnect.
Week Ending January 27, 2024
The following procedure(s) were updated:
- All brake pad replacement procedures: Add caution on making sure the front brake pad clip is properly installed.
- Halfshaft - Rear Drive Unit - LH (Remove and Replace) - Updated EPB Service Mode reference.
Week Ending January 20, 2024
The following procedure(s) were updated:
- Drive Unit - Front (Remove and Replace) - Added a note to install a new motor ID label in hood/trunk for China, Japan and Korea.
- Drive Unit - Rear (Remove and Replace) - Added a note to install a new motor ID label in hood/trunk for China, Japan and Korea.
- Drive Unit - Rear (Plaid) (Remove and Replace) - Added a note to install a new motor ID label in hood/trunk for China, Japan and Korea.
- HV Harness - HV Battery to Rear Drive Unit (Remove and Replace) - All-new procedure made vehicle agnostic.
- Module - Body Controller - Security (Remove and Replace) - Added step for ODIN routine PROC_VCSEC_X_SET-ROOT-KEY-TO-ALL-REGIONSvia Toolbox: (link)to be run for vehicles running certain firmware versions.
Week Ending January 13, 2024
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fluids - Added part numbers of refrigerant and coolant for China only.
Week Ending January 6, 2024
The following procedure(s) were updated:
- Fluids - Added North America row to Refrigerant table.