04/09/2024 14:27:03

Headlight - LH (Remove and Replace)

Correction code 17400102 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Torque Specifications

Table 1. Torque Specifications: Headlight - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws that attach the headlight to the body
5.9 Nm (4.4 lbs-ft)
  • 10 mm socket
  • ¼ in std ratchet
  • ¼ in torque wrench (installation only)
  • 2 in extension
Reuse
Bolt that attaches the fender bracket to the body
3 Nm (2.2 lbs-ft)
  • Torx T20 socket
  • ¼ in std ratchet
  • ¼ in torque wrench (installation only)
  • 4 in extension
Reuse

Remove

  1. Enable Service Mode. See Service Mode.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the cabin intake duct. See Duct - Cabin Intake (Remove and Replace).
  4. Remove the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  5. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  6. Remove the front fascia. See Fascia - Front (Remove and Install).
  7. Disconnect the electrical connector from the LH headlight.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the connector has a red locking tab: DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  8. Remove the bolt that attaches the fender bracket to the body, and then remove the bracket from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • ¼ in torque wrench (installation only)
    • 4 in extension
  9. Remove the fastener(s) that attach the LH headlight to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The headlight might not be equipped with a lower fastener.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • ¼ in std ratchet
    • ¼ in torque wrench (installation only)
    • 2 in extension
  10. Remove the headlight from the vehicle.

Install

  1. Position the LH headlight onto the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not damage the headlight during installation.
  2. Install the fasteners that attach the LH headlight to the body.
    5.9 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The headlight might not be equipped with a lower fastener.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • ¼ in std ratchet
    • ¼ in torque wrench (installation only)
    • 2 in extension
  3. Install the bolt that attaches the fender bracket to the body.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • ¼ in torque wrench (installation only)
    • 4 in extension
  4. Connect the electrical connector for the LH headlight.
  5. Install the front fascia. See Fascia - Front (Remove and Install).
    Informational PurposesAn informational icon, calling your attention
    Note
    After connecting the front fascia electrical connections, pause the procedure to initiate a software reinstall.
  6. Perform a software reinstall concurrently with the rest of the steps in this procedure. See Software Reinstall - Touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Note
    After initiating the software reinstall, continue the front fascia installation.
  7. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  8. Install the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  9. Install the cabin intake duct. See Duct - Cabin Intake (Remove and Replace).
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Adjust the headlights: