28/05/2024 08:27:17

Shield - Dust - Brake - Rear - LH and RH (Retrofit)

Correction code 33011806 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-05-28: Updated EPB Service Mode reference.
  • 1062500-00-A Card, Magnetic Field Viewer
  • 1096075-00-A Tool, Hub Puller, Hydraulic

Remove

  1. Remove any wheel caps or covers, and then loosen the LH rear wheel lug nuts. Do not remove the wheel at this time. See Wheel Assembly (Remove and Install).
  2. Loosen the LH rear drive unit halfshaft nut.
  3. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  4. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  5. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  6. Remove and discard the LH rear drive unit halfshaft nut.
  7. Remove the LH rear brake rotor. See Brake Rotor - Rear - LH (Remove and Replace).
  8. Remove the bolts that attach the LH rear brake dust shield to the knuckle, and then remove the dust shield from the vehicle.
  9. Position the hub puller tool on the LH rear wheel studs, and then hand-tighten the wheel lug nuts (x5).
  10. Use the hub puller to separate the halfshaft from the hub splines.
    Tip: While holding the hub in position, turn the hydraulic hub puller tool handle clockwise to separate the LH rear drive unit halfshaft from the hub splines.
  11. Remove and discard the bolts that attach the LH rear hub to the knuckle, and then remove the hub from the vehicle.
    Figure 1. Halfshaft hidden for clarity
  12. Repeat steps 1 to 11 on the RH side of the vehicle.

Install

  1. Install the bolts that attach the LH rear brake dust shield to the knuckle.
    8 Nm (5.9 lbs-ft)
  2. Use a magnetic field viewing card to check the LH rear hub's tone ring.
  3. Apply approximately 1 gram of Molykote M-77 Lubricant Paste only to the hub mating face on the outboard side of the LH rear drive unit halfshaft.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not apply any lubricant to the halfshaft splines. If lubricant is mistakenly applied, wipe the splines clean with a shop towel.
    Figure 2. Lubricate the area highlighted red
  4. Position the LH rear drive unit halfshaft in the LH rear hub splines, and then install the new bolts that attach the hub to the knuckle.
    78 Nm (57.5 lbs-ft)
    Figure 3. Halfshaft hidden for clarity
  5. Hand-tighten a new rear drive unit halfshaft nut on the LH halfshaft.
  6. Install the LH rear brake rotor, but do not perform any road tests. See Brake Rotor - Rear - LH (Remove and Replace).
  7. Position the LH rear wheel on the vehicle, and then hand-tighten the LH rear wheel lug nuts.
  8. Repeat steps 1 to 7 on the RH side of the vehicle.
  9. Lower the vehicle, and then shift the vehicle into Park (this will disable EPB Service Mode).
  10. Tighten LH and RH rear wheel lug nuts. See Wheel Assembly (Remove and Install).
  11. Tighten the LH and RH rear drive unit halfshaft nuts.
    300 Nm (221.2 lbs-ft)
  12. Install any wheel caps or covers that were removed.

Torque Specifications

Table 1. Torque Specifications: Shield - Dust - Brake - Rear - LH and RH (Retrofit)
Description Torque Value Reuse/Replace Notes
LH rear brake dust shield to the knuckle
8 Nm (5.9 lbs-ft)
Replace
Hub to the knuckle
78 Nm (57.5 lbs-ft)
Reuse
LH and RH rear drive unit halfshaft nuts
300 Nm (221.2 lbs-ft)
Reuse