04/09/2024 13:55:44

Glove Box - Without Knee Airbags (Remove and Replace)

Correction code 14051012 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Remove

  1. Remove and secure the customer's belongings from the glove box, if needed.
  2. Remove the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  3. Remove the LH and RH air wave end caps. See End Cap - Air Wave - LH (Remove and Replace).
  4. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  5. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. Remove the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  7. Remove the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  8. Open the glove box.
  9. Remove the screws that attach the glove box to the IP carrier.
    Informational PurposesAn informational icon, calling your attention
    Note
    One screw may be inside the glove box and not visible in the following image.
  10. Release the clips that attach the glove box to the IP carrier.
  11. Disconnect the electrical harness from the glove box solenoid connector, the damper connector, and the puddle light connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    2 of the electrical connectors are accessed from the bottom of the instrument panel.
  12. Remove the glove box from the vehicle.

Install

  1. Bring the glove box into the vehicle, and then connect the electrical harness to the glove box solenoid connector, the damper connector, and the puddle light connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    2 of the electrical connectors are accessed from the bottom of the instrument panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Route the electrical harness from the puddle lamp forward of the divider at the linkages.
  2. Make sure that the glove box damper pin is fully seated, and not to bump the glove box damper when installing the glove box.
  3. Fasten the clips that attach the glove box to the IP carrier.
  4. Install the screws that attach the glove box to the IP carrier.
    2.3 Nm (1.7 lbs-ft)
  5. close the glove box.
  6. Install the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  7. Install the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  8. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  9. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  10. Install the LH and RH air wave end caps. See End Cap - Air Wave - LH (Remove and Replace).
  11. Install the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  12. Verify that the glove box opens normally through the touchscreen.
  13. If removed earlier, put the customer's belongings back into the glove box.