05/02/2024 16:50:55

Airbag - Curtain - LH (Remove and Replace)

Correction code 20012002 1.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2-5-2024: Added note on varying number of curtain airbag fasteners.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.

Torque Specifications

Table 1. Torque Specifications: Airbag - Curtain - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH curtain airbag to the body
9 Nm (6.6 lbs-ft)
  • 10 mm socket
  • 2 in extension
Reuse

Remove

  1. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  2. Remove the headliner. See Headliner (Non-Heat Pump) (Remove and Install).
  3. Disconnect the electrical harness from the LH curtain airbag connector.
  4. Remove the bolts that attach the front and center portions of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 2 in extension
  5. Remove the bolts that attach the rear portion of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 2 in extension
  6. Carefully release the clips (x8) that attach the LH curtain airbag to the side rail, and remove the airbag from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    If any clips are damaged, the airbag must be replaced.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The airbag should always be handled by the igniter; the igniter should never be left dangling.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.

Install

  1. Install the LH curtain airbag to the side rail, and then carefully fasten the clips (x8) that attach the airbag to the side rail.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    If any clips are damaged, the airbag must be replaced.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  2. Install and hand-tighten the bolts that attach the rear portion of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  3. Install and hand-tighten the bolts that attach the front and center portions of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  4. Torque the bolts that attach the LH curtain airbag to the body.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 2 in extension
  5. Connect the electrical harness to the LH curtain airbag connector.
  6. Install the headliner. See Headliner (Non-Heat Pump) (Remove and Install).
  7. Connect 12V power. See 12V/LV Power (Disconnect and Connect).