Fascia - Front (Remove and Replace)
     Correction code
    
                           10011002
                           0.78
                           
                           
        
          NOTE: Unless otherwise explicitly
          stated in the procedure, the above correction code and FRT reflect all of the work
          required to perform this procedure, including the linked procedures. Do not stack correction codes unless
            explicitly told to do so.
        
          NOTE: See Flat Rate
            Times to learn more about FRTs and how they are created. To provide feedback on
          FRT values, email ServiceManualFeedback@tesla.com. 
        
          NOTE: See Personal Protection to make sure wearing proper PPE when
          performing the below procedure. See Ergonomic Precautions for safe and healthy working practices.
    Correction code
    
                           10011002
                           0.78
                           
                           
        
          NOTE: Unless otherwise explicitly
          stated in the procedure, the above correction code and FRT reflect all of the work
          required to perform this procedure, including the linked procedures. Do not stack correction codes unless
            explicitly told to do so.
        
          NOTE: See Flat Rate
            Times to learn more about FRTs and how they are created. To provide feedback on
          FRT values, email ServiceManualFeedback@tesla.com. 
        
          NOTE: See Personal Protection to make sure wearing proper PPE when
          performing the below procedure. See Ergonomic Precautions for safe and healthy working practices.
      
                        
    
    
  
- 10011002, 0.78
Remove
- Remove the front license plate bracket. See Bracket - License Plate - Front (Remove and Replace).
- Remove the front fascia. See Fascia - Front (Remove and Install).
- 
          Disconnect the electrical
                        harness from the RH front turn signal/fog light connector.
          
- 
          Release the clips that
                        attach the electrical harness to the front turn signal/fog light.
          
- 
          Remove the screws that
                        attach the front turn signal/fog light to the front fascia.
          
- Use a trim tool to release the tabs (x4) that attach the front turn signal/fog light to the front fascia, and then remove the light from the front fascia.
- Repeat step 3 through step 5 for the LH front turn signal/fog light.
- 
          Disconnect the electrical
                        harness from all of the front parking distance sensors connectors
                        (x6).
          Figure 1. LH Front Parking Assist Sensor Shown 
- 
          Release the clips that
                        attach the parking distance sensors to the front fascia, and then remove the
                        sensors (x6) from the fascia.
          Figure 2. LH Front Parking Assist Sensor Shown 
- 
          Disconnect the electrical
                        harness from the ambient air temperature sensor connector.
          
- 
          Release the clips that
                        attach the electrical harness to the front fascia, and then remove the
                        electrical harness from the fascia.
          
- 
          Release the clips that
                        attach the tow hook cover to the front fascia, and then remove the cover
                        from the fascia.
          
- 
          Remove the screws that
                        attach the front fascia grille to the front fascia.
          
- 
          Release the clips (x9) that
                        attach the front fascia grille to the front fascia, and then remove grille
                        from the fascia.
          Figure 3. Top Figure 4. Bottom 
Install
Installation procedure is the reverse of removal.
- 
          Install the front fascia
                        grille onto the front fascia, and then fasten the clips (x9) that attach the
                        grille to the fascia.
          Figure 5. Top Figure 6. Bottom 
- 
          Install the screws that
                        attach the front fascia grille to the front fascia. 1.8 Nm (1.3 lbs-ft) 1.8 Nm (1.3 lbs-ft)
- 
          Install the tow hook cover
                        to the front fascia, and then fasten the clips that attach the cover to the
                        fascia.
          
- 
          Install the electrical
                        harness to the front fascia, and then fasten the clips that attach the
                        electrical harness to the fascia.
          
- 
          Connect the electrical
                        harness to the ambient air temperature sensor connector.
          
- 
          Install the parking distance
                        sensors (x6) to the front fascia, and then fasten the clips that attach the
                        sensors to the fascia.
          Figure 7. LH Front Parking Assist Sensor Shown 
- 
          Connect the electrical
                        harness to all of the front parking distance sensors connectors (x6).
          Figure 8. LH Front Parking Assist Sensor Shown 
- Install the front turn signal/fog light to the front fascia, and then fasten the tabs (x4) that attach the light to the fascia.
- 
          Install the screws that
                        attach the front turn signal/fog light to the front fascia. 2.8 Nm (2.1 lbs-ft) 2.8 Nm (2.1 lbs-ft)
- 
          Fasten the clips that attach
                        the electrical harness to the front turn signal/fog light.
          
- 
          Connect the electrical
                        harness to the RH front turn signal/fog light connector.
          
- Install the front fascia. See Fascia - Front (Remove and Install).
- Install the front license plate bracket. See Bracket - License Plate - Front (Remove and Replace).
- 
          Perform a radar sensor
                        calibration only if the front radar sensor likely moved outside of its
                        calibration tolerance (due to front end collision, contact while removing
                        the fascia, etc.). See Sensor - Radar - Front (Calibration).
          NoteIf radar sensor calibration is required, add the correction code separately.