2026-02-05

Module - Restraint Control (Heat Pump) (Remove and Install)

Correction code 20015011 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-02-04: Released new procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Supplementary Restraint System (SRS) components can be hazardous if not handled properly. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
While performing any Supplementary Restraint System (SRS) related repairs, it is important to disconnect 12V/LV power, by disconnecting the 12V/LV battery and the First Responder Loop. If the vehicle’s 12V/LV power is NOT disconnected and the Restraint Control Module is removed or disturbed, this can result in the deployment of the vehicle’s airbags.

Remove

  1. Open all the doors and lower the windows.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the vehicle is being powered down, latch the rear doors to prevent accidental closure.
  2. Enable Service Mode Plus. See Service Mode Plus
  3. On the touchscreen, touch Service Mode > Safety & Restraints > Airbags > RCM > Disarm RCM, touch Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that airbags are disarmed after the routine has completed.

    Model Y shown, other models similar

  4. Open the hood.
  5. Remove the center console assembly from the vehicle. See Center Console (2.0) (Remove and Install).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Make sure LV is disconnected before continuing to the next step.
  6. Release the locking tabs, release the connector levers, and disconnect the restraint control module connectors (x2).
  7. Remove and discard the nuts (x3) that attach the restraint control module to the vehicle, and then remove the module from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Position the restraint control module into vehicle, and then install new nuts (x3) that attach the module to the vehicle.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify that the part number on the new module is correct.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  2. Connect the restraint control module connectors (x2), and then engage the locking levers and connector locks.
  3. Install the center console assembly into the vehicle. See Center Console (2.0) (Remove and Install).
  4. On the touchscreen, touch Service Mode > Safety & Restraints > Airbags > RCM > Re-arm RCM, touch Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the airbags are armed after the routine has completed.
  5. Exit Service Mode Plus. See Service Mode Plus