25/03/2024 01:14:30

Actuator - Lower Mode (Non-Heat Pump) (Remove and Replace)

Correction code 18102502 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the center console. See Center Console (Remove and Install).
  2. Release the IP harness clips (x2) and carpet clip from the RH cross car beam.
  3. Remove the bolt that attaches the RH cross car beam to the HVAC assembly.
    Tip: Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
    • 10 mm 12-point deep socket
  4. Remove the bolt that attaches the RH cross car beam bracket to the cross car beam.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13mm socket
    • 3 in extension
  5. Remove the nut that attaches the RH cross car beam bracket to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slightly pull the RH carpet towards the RH side of vehicle. Take note of the direction of the cross car beam bracket during removal.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13mm socket
    • 3 in extension
  6. Remove the RH cross car beam bracket from the vehicle.
  7. Insert the inflatable air bag up to the bottom of the lower mode actuator, then inflate it between the RH cross car beam bracket and lower HVAC assembly.
  8. Remove the bolts(x2) that attach the lower mode actuator to the HVAC assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    A mini ratchet bit can be inserted behind the harness to reach the forward fastener.
  9. Disconnect the lower mode actuator electrical connector, and then remove the actuator from the HVAC assembly.

Install

  1. Connect the lower mode actuator electrical connector.
  2. Position the lower mode actuator on the HVAC assembly, align the guide, and then push the lower mode actuator towards the left to install.
  3. Install the bolts(x2) that attach the lower mode actuator to the HVAC assembly.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    A mini ratchet bit can be inserted behind the harness to reach the forward fastener.
  4. Deflate and remove the inflatable air bag between the RH cross car beam bracket and lower HVAC assembly.
  5. Position the RH cross car beam bracket to the body.
  6. Loosely install the nut that attaches the RH cross car beam bracket to the body.
  7. Loosely install the bolt that attaches the RH cross car beam bracket to the cross car beam.
  8. Loosely install the bolt that attaches the cross car beam to the HVAC assembly.
  9. Tighten the nut that attaches the RH cross car beam bracket to the body.
    25 Nm (18.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13mm socket
    • 3 in extension
  10. Tighten the bolt that attaches the RH cross car beam bracket to the cross car beam.
    25 Nm (18.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13mm socket
    • 3 in extension
  11. Tighten the bolt that attaches the RH cross car beam to the HVAC assembly.
    5.5 Nm (4.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • 10 mm 12-point deep socket
  12. Install the IP harness clips (x2) and carpet clip to the RH cross car beam.
  13. Install the center console. See Center Console (Remove and Install).