10/12/2024 16:36:55

Glass - Door - LH - Rear (Remove and Replace)

Correction code 11500302 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-12-10: Added new caution about Pre-Installation Glass Inspection service requirements.
  • 2023-05-24: Added cleaning instructions to prevent glass damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The side impact airbag deployment depends on the rear door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the rear door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the rear doors and their components.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in Pre-Installation Glass Inspection before beginning this procedure.

Torque Specifications

Table 1. Torque Specifications: Glass - Door - LH - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH rear door glass to the regulator isolator clamps
9.5 Nm (7.0 lbs-ft)
  • 13 mm socket
  • Flex head ratchet/flex head torque wrench
  • 2 in extension
Replace
  • 1135305-00-A Tool, Window Switch Bypass, Model 3
  • 1129348-00-A XP-10 Power Supply, XP-10

Remove

  1. Remove the rear LH door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  2. Remove the LH rear door inner belt seal. See Seal - Inner Belt - Rear Door - LH (Remove and Replace).
  3. Remove the plugs that cover the opening in the door for access to the bolts.
  4. Temporarily connect the puddle light to the LH rear door harness.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Route the electrical cable so that it will not be damaged when closing the door.
  5. Connect the window switch special tool and lower the door glass so that the regulator isolator clamp bolts are accessible from the holes.
  6. Remove and discard the bolts that attach the door glass to the regulator isolator clamps, and then remove the door glass from the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the glass up and then away from the run channel to remove it from the door.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace the regulator isolator clamps, if damaged.

Install

  1. Inspect the regulator isolator clamps for glass splinters or other debris, and clean them if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  2. Position the door glass into the rear door.
  3. Install the new bolts that attach the door glass to the regulator isolator clamps.
    9.5 Nm (7.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  4. Install the inner belt seal to the rear door; attach the inner belt seal with clips.
    Tip: Press the inner belt seal down into the rear door.
  5. Adjust the door glass. See Glass - Door - LH - Rear (Adjust).
  6. Install the rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  7. Calibrate the windows. See Window Regulator (Recalibrate).