11/01/2022 03:41:32

Headlights - Adjust - EMEA (Tool Method)

Correction code 17409150 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Special tools required for this procedure:


Supplier	Part Number	Description
Tesla	1133367-00-A	Beissbarth Headlight Tester, Model 815

Identify Headlight Type

This procedure is NOT applicable to the "Global" style headlight. The global headlight (2) has a different reflector and lens design compared to the SAE/ECE headlight (1), illustrated below. For instructions on adjusting the global headlight, see Headlights - Adjust - Global (Wall Method) or Headlights - Adjust - Global (Tool Method).

Adjust Headlights Using a Headlight Tester

Note

This procedure can only be used on vehicles built after June 30, 2019. Vehicles built before this date must be adjusted via the wall method; see Headlights - Adjust - EMEA (Wall Method).

Enter headlight adjustment mode:
1. On the vehicle touchscreen, touch Controls > Service > Adjust Headlights.
2. If prompted to calibrate the headlights (Figure A), continue to substep c. If prompted to adjust the headlights (Figure B), skip to step 2.
  
  Figure 1. Figure A
  
  Figure 2. Figure B
3. Follow the prompts on the touchscreen to calibrate the headlights. Calibration is complete when all 4 checks have transitioned from "red" to "green".
  Note
  The calibration drive can take up to 2 km (1.24 mi).
  Note
  To ensure an accurate calibration:
  After turning on the drive rails, wait for at least 1 second before switching to Drive.
  Close all vehicle doors and do not open the doors while performing the calibration drive.
  After stopping the vehicle, wait at least 1 second before opening the doors.
  Do not drive the vehicle in reverse for more than 10 meters. If this is unavoidable due to garage logistics, start the headlight calibration after the vehicle has exited the garage.
4. After headlight calibration is complete, the headlights can be adjusted. Continue to the next step.
Park the vehicle on a level surface.
Make sure that all 4 tires are inflated to specification.
Open the front trunk hood.
Turn on the headlights.
Position 75 kg of ballast in the driver seat.
Position the headlight tester tool ~11 in. (30 cm) from the front of the LH headlight lens.
Adjust the height of the headlight tester tool to ~27.5 in. (70 cm) above the ground to align with the center point of the headlamp.
Connect the headlight tester tool to an electrical outlet, and then turn on the headlight tester tool.
Adjust the knobs on the base of the headlight tester tool until the tool is leveled, as indicated by the bubble gauge on the tool.

Note
The bubble must be entirely inside of the center ring in order to properly align the headlights.
Turn on the alignment laser near the top of the tool, and then rotate the tool as necessary to align the laser with the base of both hood struts.

Figure 3. LH Hood Strut
On the headlight tester tool, select Test EC > Applications > Free Test.
On the headlight tester tool, select Vehicle, and then use the + or - buttons to change the vehicle type to "Car".
On the headlight tester tool, select Headlight, and then use the + or - buttons to change the Headlight type to "EU Asym".
On the headlight tester tool, select Light, and then use the + or - buttons to change the Light type to Bi-LED.
On the headlight tester tool, select Inclination, and then use the + or - buttons to set the inclination to "-1.0%".
On the headlight tester tool, select Height, and then use the + or - buttons to change the height to "70 cm".
On the headlight tester tool, select OK and then select OK again to skip the Fog Light setup screen.
On the headlight tester tool, select the "laser beam" button to turn on the headlight laser guide.
Adjust the headlight laser guide crosshair to line up with the vertical and horizontal marks on the LH headlight (see image A).
Note
Some early production headlights do not have the vertical and horizontal headlight marks. In this case:
Adjust the height of the machine to 70 cm as indicated on the machine height adjustment post (see image B).
Measure 14.7 cm from the front corner of the front fender to the bottom edge of the headlight (see image B).
Note
Alternatively, the laser guide crosshair can be aimed at the brightest spot on a piece of paper placed against the headlight.
Figure 4. Image A: Approximate locations of the headlight markings are indicated by the small blue lines

Figure 5. Image B: Manual alignment of laser guides when headlight markings are not available
On the headlight tester tool, select the "laser beam" button to turn off the headlight laser guide.
If not already activated, enter headlight adjustment mode. On the vehicle touchscreen, touch: Controls > Service > Adjust Headlights.
On the headlight tester tool, select the "Left low beam" button on the left side of the screen, and then select the "Low beam" button at the bottom of the screen.

Note
Make sure that High beam is not selected.

Note
The "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
On the vehicle touchscreen, select Left.
On the steering wheel, use the left scroll wheel to adjust the beam level. When adjusted to within specification, the beam indicator on the headlight tester tool will change from red to green.

CAUTION
Do not sit in the vehicle, as this will affect headlight alignment.

Note
There might be a delay between the scroll wheel input and actual headlight adjustment output.
On the headlight tester tool, select the "Save" button to record the results.
Roll the headlight tester tool to the RH headlight, position the tool ~30 cm from the front of the RH headlight lens.
Align the tool to the RH headlight (see steps 19 to 21).
On the headlight tester tool, select the "Right low beam" button on the right side of the screen, and then select the "Low beam" button at the bottom of the screen.

Note
Make sure that High beam is not selected.

Note
The "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
On the vehicle touchscreen, select Right.
On the steering wheel, use the left scroll wheel to adjust the beam level. When adjusted to within specification, the beam indicator on the headlight tester tool will change from red to green.

CAUTION
Do not sit in the vehicle, as this will affect headlight alignment.

Note
There might be a delay between the scroll wheel input and actual headlight adjustment output.
On the headlight tester tool, select the "Save" button to record results, and then select "Save" again to view the results.
Close the front trunk hood.
On the touchscreen, exit headlight adjustment mode.