11/04/2023 19:28:19

Shroud - Lower - Steering Column (Remove and Replace)

Correction code 32051202 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open the LH front door and fully lower all windows.
  2. Set the vehicle's front wheels straight and the steering wheel centered.
  3. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  4. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Remove the driver airbag. See Airbag - Driver (Remove and Replace).
  6. Remove the steering wheel. See Steering Wheel (Remove and Install).
  7. Release the clips that attach the steering column upper shroud to the lower shroud, and then pull the upper shroud up.
  8. Remove the upper screws that attach the steering column lower shroud to the steering column.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • 2 in extension
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
      • Torx T20 bit, 70 mm
      • Wiha ¼ in bit holder adapter
      • Wiha torque setter
  9. Remove the lower screw that attaches the steering column lower shroud to the steering column, and then remove the lower shroud from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • 2 in extension
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
      • Torx T20 bit, 70 mm
      • Wiha ¼ in bit holder adapter
      • Wiha torque setter

Install

  1. Position the steering column lower shroud onto the steering column, and then install the lower screw that attaches the shroud to the steering column.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • 2 in extension
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
      • Torx T20 bit, 70 mm
      • Wiha ¼ in bit holder adapter
      • Wiha torque setter
  2. Install the upper screws that attach the steering column lower shroud to the steering column.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • 2 in extension
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
      • Torx T20 bit, 70 mm
      • Wiha ¼ in bit holder adapter
      • Wiha torque setter
  3. Install the clips that attach the upper shroud to the lower shroud.
  4. Install the steering wheel. See Steering Wheel (Remove and Install).
  5. Install the driver airbag. See Airbag - Driver (Remove and Replace).
  6. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).