07/05/2020 17:00:00

Adjustable Top Loop (Remove and Replace)

Correction code 20051002 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Adjustable Top Loop (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Patch bolt that attaches the upper D-ring to adjustable top loop
20 Nm (14.7 lbs-ft)
  • Torx T50 socket
  • 3/8 in std ratchet
  • 3/8 in flex head torque wrench (installation only)
  • 3 in extension
Replace
Bolt that attaches the adjustable top loop to the B-pillar
20 Nm (14.7 lbs-ft)
  • Torx T47 socket
  • 3/8 in std ratchet
  • 3/8 in flex head torque wrench (installation only)
Replace

Remove

  1. Open both LH doors and lower both LH windows.
  2. Move the LH front seat fully forward.
  3. Release the clips that attach the LH upper B-pillar trim to the vehicle.
    Tip: Release the clips at the bottom of the LH upper B-pillar trim first, and then release the clips at the top of the trim.
  4. Set the LH upper B-pillar trim aside.
  5. Remove and discard the patchbolt that attaches the upper D-ring to the B-pillar.
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • 3/8 in std ratchet
    • 3/8 in flex head torque wrench (installation only)
    • 3 in extension
  6. Remove the bolt that attaches the adjustable top loop to the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    The patchbolt is permanently attached to the adjustable top loop.
    Tip: Use of the following tool(s) is recommended:
    • Torx T47 socket
    • 3/8 in std ratchet
    • 3/8 in flex head torque wrench (installation only)
  7. Pull the top of the adjustable top loop away from the B-pillar, and then slide upwards to remove the adjustable top loop from the vehicle.

Install

  1. Position the adjustable top loop on the B-pillar, and then install the new patchbolt that attaches the adjustable top loop to the B-pillar.
    20 Nm (14.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T47 socket
    • 3/8 in std ratchet
    • 3/8 in flex head torque wrench (installation only)
  2. Install the new patchbolt that attaches the upper D-ring to the B-pillar.
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • 3/8 in std ratchet
    • 3/8 in flex head torque wrench (installation only)
    • 3 in extension
  3. Lower the adjustable top loop to align it with the LH upper B-pillar trim.
  4. Insert the top portion of the LH upper B-pillar trim under the headliner to align the clips, and then press the bottom of the trim to fully engage all of the clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the rubber door seals completely overlap the trim.