08/08/2023 05:14:34

Module - Cooling Fan (Heat Pump) (Remove and Install)

Correction code 18201311 1.14 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-08-08: Added reference to Cooling System (Vacuum Refill).
Informational PurposesAn informational icon, calling your attention
Note
This procedure services the cooling fan module on vehicles with the heat pump system. To perform this procedure on pre-heat pump vehicles, go here.

Torque Specifications

Table 1. Torque Specifications: Module - Cooling Fan (Heat Pump) (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the underhood storage unit reinforcement bracket to the cooling fan
16 Nm (11.8 lbs-ft)
  • 10 mm socket
  • 2 in extension
Reuse
Bolts that attach the lower LH and RH of the cooling fan module to the ankle catcher
10 Nm (7.4 lbs-ft)
  • 8 mm socket
  • Flex head ratchet/flex head torque wrench
  • 4 in extension
Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  3. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  4. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Release the connector lock, and then disconnect the active grille shutter electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not push down on the red tab. Pull the red tab to release the connector lock.
  6. Remove the ambient temperature sensor cover from the active griller shutter, and then disconnect the sensor electrical connector.
  7. Release the clip that attaches the front harness to the front underhood storage unit reinforcement bracket.
  8. Remove the bolts that attach the underhood storage unit reinforcement bracket to the cooling fan, and then slide the bracket rearward for clearance.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 2 in extension
  9. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  10. Remove the front valance. See Valance - Front Fascia (Remove and Replace).
  11. Place coolant drain container underneath the LH front of the vehicle.
  12. Release the clip that attaches the radiator inlet hose to the cooling fan module, disconnect the hose, allow the coolant to drain, and then plug the male and female fittings.
  13. Place coolant drain container underneath the RH front side of the vehicle.
  14. Release the clip that attaches the radiator outlet hose from the cooling fan module, disconnect the hose, allow the coolant to drain, and then plug the male and female fittings.
  15. Disconnect the electrical harness from the cooling fan module connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure to plug the coolant hoses before disconnecting the connector to avoid coolant damaging the connector.
  16. Remove the bolts that attach the lower LH and RH sides of the cooling fan module to the ankle catcher.
    Informational PurposesAn informational icon, calling your attention
    Note
    With assistance, lift up on the cooling fan module to ease the removal of the bolts.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 1. LH Side
    Figure 2. RH Side
  17. Remove the cooling fan module assembly from the vehicle.

Install

  1. With assistance, position the cooling fan module assembly into the vehicle, and then loosely install the bolts that attach the module assembly to the vehicle.
  2. Torque the bolts that attach the LH and RH of the cooling fan module to the vehicle.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Assistance is recommended to support the assembly.
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 3. LH Side
    Figure 4. RH Side
  3. Remove the plugs from the radiator outlet hose, connect the male and female fittings, and then fasten the hose clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  4. Remove the plugs from the radiator inlet hose, connect the male and female fittings, and then fasten the hose clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  5. Connect the electrical harness from the cooling fan module connector.
  6. Install the front valance. See Valance - Front Fascia (Remove and Replace).
  7. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  8. Lower the vehicle until the tires touch the ground.
  9. Position the underhood storage unit reinforcement bracket onto the cooling fan, and then install the bolts that attach the bracket to the fan.
    16 Nm (11.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 2 in extension
  10. Install the clip that attaches the front harness to the front underhood storage unit reinforcement bracket.
  11. Connect the ambient temperature sensor electrical connector, and then install the sensor cover onto the active griller shutter.
  12. Connect the active grille shutter electrical connector, and then engage the connector lock.
  13. Perform a cooling system vacuum refill. See Cooling System (Vacuum Refill)
  14. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  15. Close the LH front door and raise the LH front window.