12/01/2024 01:38:40

Link - Compliance - Lower - Front - LH (Remove and Replace)

Correction code 31013602 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-01-15: Expanded the installation section since the fasteners' installation order is different from the removal order.
Table 1. Torque Specifications: Link - Compliance - Lower - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut that attaches the front LH lower compliance link to the knuckle
180 Nm (132.7 lbs-ft)
  • Ratchet/torque wrench
  • Torx T45 socket
  • 22 mm socket
  • Combination Wrench 12pt 22mm
 Replace
Bolt and nut that attach the link to the front subframe
115 Nm (84.8 lbs-ft)
115 Nm (84.8 lbs-ft)
  • 21 mm socket
  • 21 mm deep socket
  • Cordless Ratchet/Impact Driver
  • 6 in extension
  • Combination Wrench 12pt 21mm
  • Ratchet/torque wrench
Reuse

Remove

  1. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  2. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  3. Remove and discard the nut that attaches the front LH lower compliance link to the knuckle.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx T45 socket
    • 22 mm socket
    • Combination Wrench 12pt 22mm
  4. Remove the bolt and nut that attach the link to the front subframe, and then remove the link from the subframe and knuckle.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm socket
    • 21 mm deep socket
    • Cordless Ratchet/Impact Driver
    • 6 in extension
    • Combination Wrench 12pt 21mm
    • Ratchet/torque wrench

Install

  1. Install the LH front lower compliance link to the front subframe.
  2. Hand-tighten the bolt and nut that attach the link to the front subframe.
  3. Hand-tighten a new nut to attach the front LH lower compliance link to the knuckle, and then torque the nut.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter hold the nut with a T45 socket. Mark with a paint pen.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx T45 socket
    • 22 mm socket
    • Combination Wrench 12pt 22mm
  4. Torque the bolt and nut that attach the link to the front subframe.
    115 Nm (84.8 lbs-ft)
    115 Nm (84.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark with a paint pen.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm socket
    • 21 mm deep socket
    • Cordless Ratchet/Impact Driver
    • 6 in extension
    • Combination Wrench 12pt 21mm
    • Ratchet/torque wrench
  5. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).