16/12/2021 14:37:59

Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace)

Correction code 20101002 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.

Torque Specifications

Table 1. Torque Specifications: Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the pretensioner to the seat track
40 Nm (29.5 lbs-ft)
  • Torx T50 socket
  • 3/8 in std ratchet
  • 3/8 in torque wrench (installation only)
  • 3 in extension
Replace

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the LH front seat to the foremost position and raise the seat fully.
  3. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  4. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  5. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  6. Remove the driver seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
  7. Release the connector lock, and then disconnect the electrical connector from the pretensioner.
  8. Remove the bolt that attaches the pretensioner to the seat track.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • 3/8 in std ratchet
    • 3/8 in torque wrench (installation only)
    • 3 in extension
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is attached to the pretensioner with a metal clip. The pretensioner and bolt must be replaced as an assembly.
  9. Remove the 1st row outboard lap pretensioner from the seat track.

Install

  1. Install the new pretensioner and bolt assembly to the seat track, and then tighten the bolt that attaches the pretensioner to the seat track.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 socket
    • 3/8 in std ratchet
    • 3/8 in torque wrench (installation only)
    • 3 in extension
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the pretensioner guide pin to the seat track.
  2. Connect the pretensioner electrical connector.
  3. Install the driver seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
  4. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).