29/04/2021 20:45:32

Actuator - Upper Mode (Non-Heat Pump) (Remove and Replace)

Correction code 18102602 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the 2nd lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  4. Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  5. Remove the LH air wave end cap. See End Cap - Air Wave - LH (Remove and Replace).
  6. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  7. Remove the front passenger floormat.
  8. Remove the RH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  9. Remove the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  10. Remove the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace).
  11. Remove the RH air wave end cap. See End Cap - Air Wave - LH (Remove and Replace).
  12. Remove the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  13. Remove the glove box. See Glove Box - With Knee Airbags (Non-Heat Pump) (Remove and Replace).
  14. Remove the RH footwell duct. See Duct - Footwell - RH (LHD) (Remove and Replace).
  15. Release the clips that attach the instrument panel harness to the RH side of the HVAC assembly.
  16. Disconnect the electrical connector from the upper mode actuator.
  17. Remove the bolts that attach the upper mode actuator to the HVAC assembly, and then remove the upper mode actuator.

Install

  1. Position the upper mode actuator onto the HVAC assembly; align the guide and push the actuator towards the left to install.
  2. Install the bolts that attach the upper mode actuator to the HVAC assembly.
    1.2 Nm (.9 lbs-ft)
  3. Connect the upper mode actuator electrical connector.
  4. Install the clips that attach the instrument panel harness to the RH side of the HVAC assembly.
  5. Install the RH footwell duct. See Duct - Footwell - RH (LHD) (Remove and Replace).
  6. Install the glove box. See Glove Box - With Knee Airbags (Non-Heat Pump) (Remove and Replace).
  7. Install the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  8. Install the RH air wave end cap. See End Cap - Air Wave - LH (Remove and Replace).
  9. Install the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace).
  10. Install the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  11. Install the RH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  12. Install the front passenger floormat.
  13. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  14. Install the LH air wave end cap. See End Cap - Air Wave - LH (Remove and Replace).
  15. Install the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  16. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  17. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  18. Install the 2nd lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).