23/11/2022 15:28:56

Harness - Filter - Antenna - RH (Remove and Replace)

Correction code 17108402 0.25 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open all the doors and fully lower all the windows.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the vehicle is being powered down, latch the rear doors to prevent accidental closure.
  2. Move the LH and RH front seats fully forward.
  3. Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  4. Remove the LH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  5. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  6. Release the clip and tabs (x4) that attach the LH rear C-pillar trim to the body, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the rear of the trim forward, and then upward to remove it.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  7. Remove the RH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  8. Remove the RH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  9. Remove the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  10. Release the clip and tabs (x4) that attach the RH rear C-pillar trim to the body, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the rear of the trim forward, and then upward to remove it.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  11. Remove the package tray trim. See Trim - Package Tray (Remove and Replace).
  12. Disconnect the RH antenna filter harness connector from the tuner.
    Tip: Use of the following tool(s) is recommended:
    • Small flat head screwdriver
  13. Disconnect the RH antenna filter harness connector from the tuner and body harness.
    Tip: Use of the following tool(s) is recommended:
    • Small flat head screwdriver
  14. Release the clip that attaches the RH antenna filter harness to the body.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  15. Remove the RH antenna filter harness from the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Peel the tape back found at each end of harness housing seal.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  16. Disconnect the RH antenna filter harness connector from the heater grid, and then remove the harness from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Gently disconnect the harness. Do not damage the heater grid.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in

Install

  1. Position the RH antenna filter harness on the vehicle, and then connect the harness connector to the heater grid.
  2. Install the clip that attaches the RH antenna filter harness to the body.
  3. Connect the RH antenna filter harness connector to the tuner and body harness.
  4. Connect the RH antenna filter harness connector to the tuner.
  5. Install the RH antenna filter harness on the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply a small piece of tape at each end of the seal clip.
    Tip: Use of the following tool(s) is recommended:
    • Felt tape
    • Scissors
  6. Install the package tray trim. See Trim - Package Tray (Remove and Replace).
  7. Install the clip and tabs (x4) that attach the LH rear C-pillar trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the back tabs into package tray, and then push the front tabs toward the rear.
  8. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  9. Install the LH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  10. Install the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  11. Raise the LH 2nd row seat.
  12. Repeat step 7 through step 11 for the RH side of the vehicle.
  13. Move the LH and RH front seats to the original positions.
  14. Raise all the windows and close all the doors.