04/09/2024 14:25:05

Harness - Seat - Driver (Remove and Replace)

Correction code 17101802 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 1082447-07-A Torx Plus T45
Informational PurposesAn informational icon, calling your attention
Note
The below procedure describes the removal of the driver's seat harness on a LHD model. The procedure for RHD models is similar while illustrations may be mirror-imaged.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Remove

  1. Open all four doors
    Informational PurposesAn informational icon, calling your attention
    Note
    If vehicle is being powered down, Latch rear doors to prevent accidental closure
  2. Lower all four windows
  3. Move the LH front seat to most rearward and lowest position
  4. Remove inboard side shield from LH front seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Once front clip is released, Release rear of trim and rotate upward then feed buckle through slot to remove
  5. Disconnect LH front seat buckle connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  6. Release the clip that attaches the seat belt buckle connector to the seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x fir tree clip
  7. Remove the clips securing the seat belt buckle connector harness to the seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fir tree clips
  8. Move LH front seat forward
  9. Move RH front seat forward
  10. Remove 2nd row seat cushion and disconnect harness
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 2x connectors, Press tab toward LH side of vehicle on each side to release front edge of seat cushion
  11. Open hood
    Informational PurposesAn informational icon, calling your attention
    Note
    Press "Open" button on the touchscreen to release the latch, Lift the lid manually
  12. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    Note
    12x clips, Only store rear apron visible face upwards
  13. Remove LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  14. Remove LH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
  15. Remove clip for LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x push clip
  16. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
  17. Release seat belt retractor from LH front seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust seat if needed, Insert special removal tool into the bottom of the retractor to release
  18. Fully recline RH seat to allow for headrest removal
  19. Install the outboard headrest release tool
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress the material around the headrest post to expose the release clip, Ensure both tangs of the release tool engage the retaining spring, The release tool is rotated into position, Images show headrest removed for clarity
  20. Install the inboard headrest release tool
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress the material around the headrest post to expose the release clip, Ensure both tangs of the release tool engage the retaining spring, The release tool is rotated into position, Images show headrest removed for clarity
  21. Remove the headrest from seat
    Informational PurposesAn informational icon, calling your attention
    Note
    2x locking clips, Remove by pulling straight up, out of the seat
  22. Remove the inboard headrest release tool
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the release tool out of position, Do not pull straight up or out
  23. Remove the outboard headrest release tool
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the release tool out of position, Do not pull straight up or out
  24. Remove seat back from LH front seat
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, Start at the top of the seat and pull the shell away from the frame, When the side clips are free, pull the bottom and carefully roll the bottom tabs out of the slots, If pulled straight out the clips on the seat back can break off, Release remaining clips from underneath seat assembly, Move seat as needed for access
  25. Move LH front seat rearward and upward position
  26. Tilt seat back to forward position
  27. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > Safety & Security > Vehicle Power > Power Off, Confirm power off at warning dialogue box
  28. Disconnect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 6 Nm, Ensure the vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
  29. Remove 12V cap from ancillary bay
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cap
  30. Disconnect HVC logic connector and install logic cap
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x cap, Release locking tab then push the handle downward to release connector
  31. Remove the lower flap covering the outboard corner of the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the trim straight up, off of the retaining tabs to release
  32. Remove the upper flap covering the outboard corner of the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the lower section of trim away from the retaining tab to release, then pull the trim straight up off of the upper retaining tab
  33. Remove the outer clips securing the seat upholstery to the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, To release, rotate the clips off of the frame from the inside out
  34. Pull the seat upholstery away from the air bag to gain access to the air bag electrical connector
  35. Disconnect driver seat air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Pull both of the orange tabs down to release the connector
  36. Remove the harness clip securing the airbag pigtail to the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x fir tree clip
  37. Disconnect the recliner motor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  38. Disconnect the lumbar valve pack and ECU
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  39. Disconnect the lumbar pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  40. Remove the seat harness from seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  41. Remove screw securing outer side cover to seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 4 Nm, Ensure the front of the seat is high enough to access the T20 screw
  42. Release outer side cover clip from seat, but do not remove
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Do not fully remove, possible damage to the trim/switch pack/harness
  43. Disconnect seat switch connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  44. Slide outer cover rearward to release clip from frame and lift up over pretensioner to remove
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  45. Remove clips securing seat switch harness to seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fir tree clips
  46. Release seat belt pretensioner harness clips
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, Use 90 pick to release harness clips from seat track rail
  47. Disconnect the seat belt pretensioner
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Pull both of the orange tabs down to release the connector
  48. Disconnect the tilt motor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  49. Remove the harness retaining clip under the tilt motor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  50. Route the seat belt pretensioner leg of the seat harness away from the seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Route the harness leg from behind the tilt motor and away from the bottom of the seat
  51. Disconnect the lift motor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  52. Disconnect the seat back heater connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Green
  53. Disconnect the heat pad connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  54. Remove clip securing the harness to the under side of the seat, next to the seat heater connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  55. Disconnect the seat occupied sensor and set the sensor harness pigtail aside
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  56. Remove the retaining clip that secures the seat occupied sensor connector to the seat bottom and discard
    Informational PurposesAn informational icon, calling your attention
    Note
    The new harness comes with the retaining clip installed on the harness connector
  57. Remove the retaining clip under the main seat harness junction
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  58. Remove the clip securing the harness to the seat cushion frame under the lift motor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  59. Disconnect LH front seat track motor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  60. Remove the clip securing the track motor harness to the track motor housing
    Informational PurposesAn informational icon, calling your attention
    Note
    1x edge clip
  61. Disconnect the seat track position sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  62. Remove the clips securing the seat belt buckle connector harness to the seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fir tree clips
  63. Disconnect LH front seat harness from left body controller
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Release white lock, Slide lock upward
  64. Release LH front seat harness from sill trim clips
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips
  65. Route the seat belt buckle leg of the harness away from the seat to allow the seat harness to be removed
    Informational PurposesAn informational icon, calling your attention
    Note
    Route the seat belt buckle leg around the lift motor and away from the seat, The harness will be completely free from the seat at this point

Install

  1. Position the new seat harness for installation
    Informational PurposesAn informational icon, calling your attention
    Note
    Route the harness under the lift motor and tilt motor placing the harness legs in the correct locations, Harness clips will be installed later
  2. Install LH seat harness to sill trim clips
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips, Tuck excess harness between 12v harness bracket and body
  3. Connect LH front seat harness to left body controller
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Engage locking tab, Tuck excess harness if equipped with MY compatible seat
  4. Connect the LH front seat belt pretensioner
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  5. Install seat belt pretensioner harness clips
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, Position seat belt pretensioner harness clips to seat track rail and press down on each clip to secure
  6. Install clips securing seat switch harness to seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fir tree clips
  7. Connect seat switch connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  8. Slide outer cover forward to engage clip into the frame and lift up over pretensioner to install
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  9. Install the retaining clip under the main seat harness junction
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  10. Install screw securing outer side cover to seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 4 Nm
  11. Install the clip securing the harness to the seat cushion frame under the lift motor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  12. Connect the seat occupied sensor and install the clip onto the seat bottom
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x retaining clip, Ensure harness is not routed between cushion and frame to avoid friction
  13. Install the clip securing the harness to the under side of the seat, next to the seat heater connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  14. Connect the heat pad connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  15. Connect the seat back heater connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  16. Install the harness retaining clip under the tilt motor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip
  17. Connect the tilt motor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  18. Connect the seat track position sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  19. Connect LH front seat track motor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  20. Install the clip securing the track motor harness to the track motor housing
    Informational PurposesAn informational icon, calling your attention
    Note
    1x edge clip
  21. Connect the lift motor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  22. Install the seat harness to seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  23. Connect the lumbar pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  24. Connect the lumbar valve pack and ECU
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  25. Connect the recliner motor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  26. Install the harness clip securing the airbag pigtail to the seat back frame
  27. Pull the seat upholstery away from the air bag to gain access to the air bag electrical connector
  28. Connect LH front seat side air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  29. Install the outer clips securing the seat upholstery to the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  30. Install the upper flap covering the outboard corner of the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the flap over the metal tangs to secure
  31. Install the lower flap covering the outboard corner of the seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the flap over the metal tangs to secure
  32. Install the seat back shell base assembly to seat back frame
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, Install the lower clips first and rotate the shell up into place, Light pressure may need to be applied to the shell to ensure it's fully seated, The headrest posts will engage the seat back when installed
  33. Hook the strap clips for the seat back shell onto the seat suspension
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Ensure the straps are tight for proper fit and installation
  34. Install the headrest into passenger seat
    Informational PurposesAn informational icon, calling your attention
    Note
    2x locking clips, Ensure the headrest is fully seated, An audible click will be heard when installing the headrest, Ensure the headrest is seated by tugging up on the headrest
  35. Remove logic cap and connect the HVC logic connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated
  36. Install 12V cap to ancillary bay
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cap
  37. Connect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 6 Nm
  38. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    Note
    12x clips
  39. Close hood
  40. Move the LH front seat to most rearward and lowest position
  41. Install the clips securing the seat belt buckle connector harness to the seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fir tree clips
  42. Install clip securing seat belt buckle harness connector to the seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x fir tree clip
  43. Connect the seat belt buckle
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  44. Install LH inner side shield to driver seat
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, Slide the trim onto the seat from the opening for the buckle, then slide forward into position
  45. Move LH front seat forward
  46. Install LH front seat retractor to seat
  47. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2 guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim
  48. Install clip for LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x push clip
  49. Install LH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
  50. Install LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  51. Connect 2nd row seat cushion harness and install 2nd row seat cushion
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 2x clips, Insert the seat belt buckles through the holes, Slide rear cushion inward then align front guide tabs to locking tabs, Make sure cushion is fully seated with push & pull test near clips
  52. Move LH front seat to original position
  53. Move RH front seat to original position
  54. Raise all windows
  55. Close all four doors
    Informational PurposesAn informational icon, calling your attention
    Note
    Unlatch rear doors before closing