04/09/2024 12:45:59

Brake Rotor - Front - LH (Remove and Replace)

Correction code 33010102 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1134786-00-A Tool, Caliper Spreader, Model 3
  • 2023-11-22: Added extra information for single rotor replacement.
Informational PurposesAn informational icon, calling your attention
Note
For detailed brake specifications, see Brakes.
Informational PurposesAn informational icon, calling your attention
Note
If only a single rotor needs replacing (due to damage), the corresponding axle rotor must be measured for runout and thickness. See Brake Rotor - Front - LH (Measure Runout).

Torque Specifications

Table 1. Torque Specifications: Brake Rotor - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH front brake hose bracket to the LH front knuckle
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • Flex head ratchet/flex head torque wrench
  • 4 in extension
Reuse
LH front caliper to the LH front knuckle
94 Nm (69.3 lbs-ft)
  • External Torx E18
  • Ratchet/torque wrench
Replace 1088969-00-B
Brake rotor to the hub
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • Flex head ratchet/flex head torque wrench
  • 2 in extension
Reuse

Remove

  1. Raise the vehicle and remove the front LH wheel. See Wheel Assembly (Remove and Install).
  2. Remove the bolt that attaches the LH front brake hose bracket to the LH front knuckle.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  3. Remove and discard the bolts that attach the LH front caliper to the LH front knuckle, remove the caliper from the knuckle, and allow the caliper to hang from an S-hook.
    94 Nm (69.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • External Torx E18
    • Ratchet/torque wrench
    Informational PurposesAn informational icon, calling your attention
    Note
    If needed, use the caliper spreader tool to push the caliper pistons to the fully open position.
  4. Remove the bolt that attaches the brake rotor to the hub, and then remove the brake rotor from the hub.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension

Install

Installation procedure is the reverse of removal, except for the following:

  1. Replace patchbolts
  2. Mark the fastener with a paint pen after torquing.
  3. Press the brake pedal at least 5 times to seat the pads against the rotor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Always check that the brake pads are seated correctly before driving the vehicle.
  4. Burnish the brake pads. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    Note
    During vehicle driving, make sure that proper brake pedal feel and performance is achieved.
    Informational PurposesAn informational icon, calling your attention
    Note
    Add correction code 33013000 to the Service Visit.