15/08/2024 00:49:33

Seat Back - 2nd Row - LH (Remove and Replace)

Correction code 13054002 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-07-23: Deleted the 2nd row seat buckle steps.
  • Torchless Heat Induction Tool - 1032900-00-A

Torque Specifications

Table 1. Torque Specifications: Seat Back - 2nd Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH 2nd row buckle to the body
40 Nm (29.5 lbs-ft)
  • 3 in extension
  • 15 mm socket
  • Cordless Ratchet/Impact Driver
  • Torchless Heat Induction Tool - 1032900-00-A (for removal only)
  • Ratchet/torque wrench
Replace
Nuts (x2) that attach the LH seatback assembly hinge bracket to the body
18 Nm (13.3 lbs-ft)
  • 13 mm socket
  • 2 in extension
  • Ratchet/torque wrench
Reuse

Remove

  1. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  2. Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  3. Fold the LH 2nd row seat into vertical position.
  4. Remove and discard the bolt that attaches the LH 2nd row buckle to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the bolt is hard to remove, use an inductive heating tool to melt the adhesive patch material. Position the inductive heating tool coil around the bolt, and then heat the bolt for 20 seconds. Allow the bolt to cool down for 2 minutes, and then remove and discard the bolt. The inductive heater coil, bolt, and adjacent areas will be extremely hot.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Persons that have a pacemaker or any other kind of electronic or metal surgical implant must stay at least 1 m (3 ft) away from the inductive heater while it is in use.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Remove all metallic items (such as coins, keys, electronics, and tools) from pockets before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Ensure that there is a properly-maintained fire extinguisher in the work area before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use the inductive heater in a well-ventilated area.
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • 15 mm socket
    • Cordless Ratchet/Impact Driver
    • Torchless Heat Induction Tool - 1032900-00-A (for removal only)
    • Ratchet/torque wrench
  5. Disconnect the electrical harness from the heated seat connector for the LH 2nd row seat back assembly, if equipped.
  6. Remove the nuts (x2) that attach the LH seatback assembly hinge bracket to the body.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • 2 in extension
    • Ratchet/torque wrench
  7. Lift the left side of the LH seat back assembly up, move forward and to the left, and pull the inner pivot out of the RH seat back assembly.
  8. Remove the LH seat back assembly from the vehicle.

Install

  1. Insert the inner pivot of the LH seat back assembly into the receptacle of the RH seat back assembly, move the assembly rearward and to the right, and then lower the LH seat back assembly hinge bracket onto the body studs.
  2. Install the nuts (x2) that attach the LH seatback assembly hinge bracket to the body.
    18 Nm (13.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • 2 in extension
    • Ratchet/torque wrench
  3. Connect the electrical harness to the heated seat connector for the LH 2nd row seat back assembly, if equipped.
  4. Install a new bolt that attaches the LH 2nd row buckle to the body.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • 15 mm socket
    • Cordless Ratchet/Impact Driver
    • Torchless Heat Induction Tool - 1032900-00-A (for removal only)
    • Ratchet/torque wrench
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  5. Install the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  6. Fold the LH 2nd row seatback to vertical position.
  7. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).