08/10/2024 17:34:25

Module - Body Controller - Security (Remove and Replace)

Correction code 17454002 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-01-17: Added step for ODIN routine PROC_VCSEC_X_SET-ROOT-KEY-TO-ALL-REGIONSvia Toolbox: (link)to be run for vehicles running certain firmware versions.
  • 2023-11-20: Updated security controller configuration steps.
  • 2023-10-24: Updated post-replacement Toolbox routines.
  • 2023-07-21: Added Note about security-related toolbox actions.
  • 2023-10-26: Added some missing tool information.
  • 2024-07-17: Updated the way of performing the routines from using Toolbox to using the touchscreen.
Informational PurposesAn informational icon, calling your attention
Note
Some of the Toolbox Actions within this procedure are related to vehicle security, and can only be performed by Tesla employees or third parties authorized to perform security-related Toolbox Actions. To learn more, see the Service Subscription FAQs available in the user account dropdown menu.

Torque Specifications

Table 1. Torque Specifications: Module - Body Controller - Security (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws that attach the security body controller module to the cup holder décor panel
1.6 Nm (1.2 lbs-ft)
  • Torx T20 socket
  • Ratchet/torque wrench
  • Wiha TorqueVario-S 0.80Nm - 2.0Nm
  • Wiha 1/4" Bit Holder Adapter
Reuse
Screws (x4) that attach the LH center console bright strip to the center console assembly
1.6 Nm (1.2 lbs-ft)
Reuse

Remove

  1. Open all doors and lower all windows.
    Informational PurposesAn informational icon, calling your attention
    Note
    Latch the rear doors with the doors open using a small flat blade screwdriver to prevent an accidental lockout.
  2. Move the driver seat and front passenger seat fully rearward and to the lowest position.
  3. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  4. Open the center console armrest fully.
  5. Remove the LH and RH center console decor trims. See Decor Trim - Center Console - LH (Remove and Replace).
  6. Remove the screws and release the tabs that attach the LH bright strip to the center console, and then remove the strip from the console. Repeat this step to remove the RH bright strip.

    LH shown, RH similar

  7. Release the clips (x6) that attach the cup holder decor panel to the cup holder assembly, and then separate the cup holder decor panel from the center console assembly.
  8. Disconnect the electrical connector from the security body controller module, and then remove the cup holder decor panel from the vehicle.
  9. Remove the screws (x2) that attach the security body controller module to the cup holder decor panel, and then remove the security body controller module from the panel.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Ratchet/torque wrench
    • Wiha TorqueVario-S 0.80Nm - 2.0Nm
    • Wiha 1/4" Bit Holder Adapter

Install

  1. Install the screws (x2) that attach the security body controller module to the cup holder decor panel.
    1.6 Nm (1.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Ratchet/torque wrench
    • Wiha TorqueVario-S 0.80Nm - 2.0Nm
    • Wiha 1/4" Bit Holder Adapter
  2. Connect the electrical connector to the security body controller module.
  3. Attach the clips (x6) that attach the cup holder decor panel to the center console assembly.
  4. Install the RH bright strips: Start with the corner nearest to the IP carrier, and then continue towards the rear. Repeat this step on the LH bright strip.
  5. Install the screws (x7) that attach the RH bright strip to the center console assembly. Repeat this step on the LH bright strip.
    1.6 Nm (1.2 lbs-ft)

    LH shown, RH similar

  6. Install the RH center console decor trim, and then repeat this step on the LH center console decor trim. See Decor Trim - Center Console - LH (Remove and Replace).
  7. Close the center console armrest.
  8. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  9. Restore the driver seat and front passenger seat back to their original position.
  10. Connect a laptop with Toolbox 3 to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Configuration changes from within Toolbox can only be performed by a Tesla employee at this time. Third parties must request the configuration change through their agreed Tesla technical support channel.
  11. Reinstall the vehicle firmware. See Software Reinstall - Touchscreen.
  12. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Low Voltage > Procedures > VCSEC Post Replacement > VCSEC Post Replacement Procedure, click Run, and allow the routine to complete.
  13. Place the key behind the cup holder, and then tap Low Voltage > Keys > Pair Key, click Run, and allow the routine to complete.
  14. Place the NFC card(s) on the NFC card reader in the center console, and check the function of the programmed NFC keys.
  15. Disconnect the laptop from the vehicle.
  16. Exit Service Mode. See Service Mode.
  17. Raise all windows and close all doors.
  18. Inform the customer that the new security body controller will not recognize any previously paired phone key. The customer must delete and re-pair their phone key to the vehicle, if they were previously using this feature. Instructions are available in the Owners Manual, and at the DIY web pages.