Vehicle Sanitation - Evaporator - Models with PTC Heater - Tunap 994 (EMEA)
Correction code
18106738
0.84
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See Personal Protection to make sure wearing proper PPE when
performing the below procedure. See Ergonomic Precautions for safe and healthy working practices.
- 1769621-00-A FOAMING CLEANER, TUNAP 994, AC EVEAPORATOR
Evaporator cleaning using Tunap 994
- Turn off A/C, set the cabin air to HI temperature, maximum blower speed and outside air intake, and then let the blower run for 8 minutes.
- Remove the cabin filters. See Filter - Cabin (Remove and Replace).
- Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
-
Disconnect the 12V
electrical connector from the PTC heater.
-
Release the clip that
attaches the PTC heater electrical harness to the HVAC module.
-
Remove the bolts that attach
the LH side of the PTC heater to the HVAC module.
-
Release the clips that
attach the PTC heater electrical harness to the HVAC module.
-
Remove the nut that attaches
the instrument panel harness ground strap to the PTC heater.
-
Remove the bolts that attach
the RH side of the PTC heater to the HVAC module, and then lower the PTC
heater from the HVAC module.
-
Remove the bolts that attach
the service panel to the standoffs on the HVAC module, and then remove the
service panel.
- Carefully slide the PTC heater out of the HVAC module and put it aside.
- Place absorbent material underneath the HVAC module.
-
Pour 1 liter of Tunap 994
hygienic cleaner into the tank of the pressure cup spray gun, and then
connect shop air to the spray gun.
-
Insert the probe in the HVAC
filter housing, and then spray all of the cleaning solution on the
evaporator.
NoteThe spray holes in the probe should face to the front of the vehicle, towards the evaporator.NoteBe sure to coat the entire evaporator with the cleaning solution.
-
Let the cleaning solution
sit on the evaporator for 30 minutes. Continue to the next steps while the
cleaning solution sits on the evaporator.
NoteRegularly check under the vehicle and adjust the coolant drain container/absorbent material as necessary.
- Install the PTC heater into the HVAC module.
-
Install the bolts that attach the RH side of the PTC heater to the HVAC
module (torque 2.9 Nm).
-
Position the IP harness ground strap onto the PTC heater stud, and then
install the nut that attaches the ground strap to the PTC heater (torque 5
Nm).
-
Install the bolts that attach the service panel to the standoffs on the
HVAC module (torque 1.2 Nm).
-
Install the clips that attach the PTC heater electrical harness to the HVAC
module.
- Install the cabin filters and fit related components. See Filter - Cabin (Remove and Replace).
-
Install the bolts that attach the LH side of the PTC heater to the HVAC
module (torque 2.9 Nm).
-
Install the PTC heater electrical harness onto the U-clip.
-
Connect the 12V electrical connector to the PTC heater.
- Connect 12V power. See 12V/LV Power (Disconnect and Connect)
- Once the cleaning solution has sat long enough, install new cabin filters. See Filter - Cabin (Remove and Replace).
- Turn on A/C, set the cabin air to LO temperature, maximum blower speed and outside air intake.
-
The cleaning foam will exit
through the HVAC drain. Continue to the next step once clean water is
observed exiting the HVAC drain.
- Remove the coolant drain container/absorbent material from under the vehicle.