20/01/2023 10:14:49

Airbag - Knee - Driver (Remove and Install)

Correction code 20010201 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.
Informational PurposesAn informational icon, calling your attention
Note
The driver knee airbag is only equipped on North American vehicles.

Torque Specifications

Table 1. Torque Specifications: Airbag - Knee - Driver (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the driver knee airbag to the vehicle
2 Nm (1.5 lbs-ft)
  • Torx T20 socket
  • ¼ in std ratchet
  • 4 in extension
  • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
    • Wiha torque setter
    • ¼ in to 3/8 in adapter
Torx T30 bolts (x4) that attach the driver knee airbag to the instrument panel
8 Nm (5.9 lbs-ft)
  • Torx T30 socket
  • ¼ in std ratchet
External Torx E10 bolts (x4) that attach the driver knee airbag to the instrument panel
8 Nm (5.9 lbs-ft)
  • External Torx E10
  • 3/8 in std ratchet
  • 3 in extension
  • ¼ in torque wrench (installation only)
    • ¼ in to 3/8 in adapter

Remove

  1. Open the all doors and fully lower all windows.
  2. Remove the LH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  3. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  4. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  5. Remove the driver footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  6. Remove the T20 bolts (x2) that attach the driver knee airbag to the vehicle.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • ¼ in std ratchet
    • 4 in extension
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
      • Wiha torque setter
      • ¼ in to 3/8 in adapter
  7. Remove and discard the bolts (x4) that attach the driver knee airbag to the instrument panel.
    8 Nm (5.9 lbs-ft)
    or
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    • ¼ in std ratchet
    or
    • External Torx E10
    • 3/8 in std ratchet
    • 3 in extension
    • ¼ in torque wrench (installation only)
      • ¼ in to 3/8 in adapter
  8. Release the clip that attaches the driver knee airbag electrical harness to the lower instrument panel.
  9. Disconnect the wiring harness connector from the driver knee airbag, and then remove the airbag from the vehicle.

Install

Installation procedure is the reverse of removal, except for the following:

Informational PurposesAn informational icon, calling your attention
Note
Install new Torx External E10 bolts (x4) on the driver knee air bag. Do not use Torx T30 bolts (pictured).
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Replace all patchbolts.
  • Make sure that the clips on the rear edge of the driver knee airbag cover engage the IP carrier.