2026-06-19

Perform General Inspection (Inspection)

Correction code 00030700 FRT 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check all windows from the master switch

Note
Document any abnormal operation/noises
Function check LH rear door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH rear door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check the exterior lights

Note
Recommend assistance, inspect and note functionality of Headlight (LH and RH), Side Repeater (LH and RH), Taillight (LH and RH), CHMSL, Fog Light (LH and RH), Reverse Light (LH and RH), Front Turn Signal (LH and RH), Rear Turn Signal (LH and RH)
Verify operation of windshield wipers and nozzles

Note
Ensure hood and doors are closed prior to activating wipers, Inspect and note functionality for wipers and wiper jets, Check for full range of motion, speed of motion, interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions
Verify operation of horn

Note
Press button on steering wheel and verify high and low tones both sound
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

Note
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

Note
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction
Open hood

Note
Press "Open" button on touchscreen to release latch, Lift lid manually
Remove rear apron

Note
12x clips, Only store rear apron visible face upwards
Remove cabin intake upper duct assembly

Note
3x clips, Some configurations may come with 4x clips
Remove closeout panel from frunk assembly

Note
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Grab closeout panel from bottom then pull it upward to release clips, Disconnect switch
Remove bolts securing frunk assembly

Note
7x bolts, 10mm, 5 Nm
Remove frunk assembly from vehicle

Note
12x clips, Replace any clips if broken or missing, Number of clips may vary on older vehicles
Perform inspection of under hood area

Note
Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Visually inspect brake fluid level
Fill washer reservoir with fluid
Inspect coolant level and top off as necessary

Note
Ensure that fluid level is at Max line
Raise and support vehicle

Note
remove charging equipment
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove outer fasteners securing front aero shield

Note
9x bolts, 10mm, 5 Nm
Remove front aero shield

Note
2x nuts, 15mm, 8 Nm
Remove rear aero shield

Note
13x bolts, 10mm, 5 Nm
Remove LH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Remove RH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Check all four tire pressures manually

Note
4x tires, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures
Record tread depth for LH front tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for LH rear tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for RH rear tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for RH front tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Inspect underside of vehicle for fluid leaks
Perform inspection of steering components

Note
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of front suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform visual inspection of HV battery enclosure

Note
Check for any dents, scrapes, or other damage
Perform visual inspection of LH front brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record LH front brake pad thickness

Note
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec: See technical data
Perform visual inspection of LH rear brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record LH rear brake pad thickness

Note
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec: See technical data
Perform visual inspection of RH rear brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record RH rear brake pad thickness

Note
Recommend replacement if 2 mm or less, Check both inboard and outboard pads
Inspect RH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec : See technical data
Perform visual inspection of RH front brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record RH front brake pad thickness

Note
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect RH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec: See technical data
Install RH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Install LH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Install rear aero shield

Note
13x bolts, 10mm, 5 Nm, Apply Loctite 222 to bolts before installing
Position front aero shield to vehicle

Note
2x nuts, 15mm, 8 Nm, Hand-tighten the nuts to temporarily hold the panel in place
Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield

Note
9x bolts, 10mm, 5 Nm
Lower vehicle fully

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Remove vehicle from lift

Note
Lower rack arms fully and remove from under vehicle
Install frunk assembly to vehicle

Note
12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles, Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam, replace any damaged clips
Install bolts securing frunk assembly

Note
7x bolts, 10mm, 5 Nm
Install frunk close out panel

Note
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
Install cabin intake upper duct assembly

Note
3x clips, Some configurations may come with 4x clips
Install rear apron

Note
12x clips
Close hood

2017-2023 Model 3 Service Manual

Perform General Inspection (Inspection)

Procedure

Figure 1

Figure 2

Figure 3