17/03/2021 18:06:55

Fascia - Front (Remove and Install)

Correction code 10011001 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Fascia - Front (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the top of the front fascia to the vehicle
4 Nm (2.9 lbs-ft)
  • 10 mm socket
  • ¼ in std ratchet
  • 2 in extension
  • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
    • ¼ in hex to ¼ in square 2 in adapter
Reuse
Bolts that attach the LH side of the front fascia to the fender
4 Nm (2.9 lbs-ft)
  • 10 mm deep socket
  • Flex head ratchet/flex head torque wrench
  • 6 in extension
  • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
    • ¼ in hex to ¼ in square 2 in adapter
Reuse
Bolt that attaches the LH corner of the front fascia to the fender
3 Nm (2.2 lbs-ft)
  • 10 mm deep socket
  • Flex head ratchet/flex head torque wrench
  • 6 in extension
  • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
    • ¼ in hex to ¼ in square 2 in adapter
Reuse
Bolt that attaches the front aero shield to the front valance
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • 4 in extension
  • Ratchet/torque wrench
Reuse

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Remove the cabin intake duct. See Duct - Cabin Intake (Remove and Replace).
  3. Remove the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  4. Remove the underhood storage unit carpet. See Carpet - Underhood Storage (Remove and Install).
  5. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  6. Remove the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • ¼ in std ratchet
    • 2 in extension
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
      • ¼ in hex to ¼ in square 2 in adapter
  7. Remove the clips (x5) that attach the front of the LH wheel arch liner to the front fascia, and then pull the liner back to access the fascia to fender bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Turn the steering wheel to the right for additional clearance.
    Tip: Although not necessary to perform this procedure, consider placing the vehicle on a 2-post lift to gain better access to the fasteners in the following steps.
  8. Loosen the forward bolts (x2) that attach the LH side of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
      • ¼ in hex to ¼ in square 2 in adapter
  9. Remove the outermost bolt that attaches the LH corner of the front fascia to the fender.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 6 in extension
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
      • ¼ in hex to ¼ in square 2 in adapter
  10. Repeat steps 7 to 9 on the RH side of the vehicle.
  11. Disconnect the electrical connector from the front fascia in the RH wheel well.
    Tip: Slide the locking tab away from the connector, and then press down on the tab to release the connector.
  12. Remove the bolts (x4) that attach the front aero shield to the front valance.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
    • Ratchet/torque wrench
  13. Remove the clips (x1 on each side) that attach the lower valance to the front stabilizer bar brackets.
  14. If present, release the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  15. If present, slide the locking tab away from the connector, and then press down on the locking tab to disconnect the connector from the pedestrian warning speaker assembly.
  16. With an assistant, release both corners of the front fascia, and then carefully pull the fascia forward to remove it from the vehicle. Place the fascia on a padded surface.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully release the tabs that attach the lower headlight bracket to the front fascia, otherwise the tabs can be broken.
    Tip: Perform this step with the help of another technician.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The corners of the ankle catcher are very sharp and might cause personal injury.

    LH ankle catcher corner shown; RH corner similar

Install

Installation procedure is the reverse of removal, except for the following:

  • Align the fascia to the fender before tightening the bolts that attach the fascia to the fender.
  • Perform a radar sensor calibration only if the front radar sensor likely moved outside of its calibration tolerance (contact while removing the fascia, etc.). See Sensor - Radar - Front (Calibration).
    Informational PurposesAn informational icon, calling your attention
    Note
    If radar sensor calibration is required, add the correction code separately.
  • Apply a thin bead of Loctite 222 to the threads of the bolts (x4) that attach the front aero shield panel to the vehicle.