15/03/2024 06:33:32

Tire - Front - LH (Road Force) (Balance)

Correction code 34022005 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-04-04: Added Road Force Peak to Peak values.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Always read and understand the tire equipment operator’s manual and on-screen instructions before operating the wheel balancer or tire changer.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Always make sure to properly secure the wheel and exercise caution around all moving parts and pinch points, including the indent rollers. Additionally, secure all loose items such as hair, jewelry, and clothing, so that they will not catch on moving parts.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The machine must be operated by no more than one person at a time. Other persons must maintain a safe distance of at least three feet from equipment while in use.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Never use equipment that is defective or not working as expected based on the equipment operator’s manual.
Informational PurposesAn informational icon, calling your attention
Note
These instructions are based on the Hunter GSP9700 wheel balancer. Some steps might be different for other wheel balancers. Refer to the operator's manual and on-screen instructions for specific information.

Balance

Informational PurposesAn informational icon, calling your attention
Note
Perform this procedure once the wheel has been removed from the vehicle.
  1. Refer to the Tire and Loading Information label located on the driver side B-pillar, and record the correct tire pressure, depending on suspension type, tire size, and region.
  2. Install the proper inner cone adapter on the wheel balancer.
  3. Place the wheel on the balancer with the face of the wheel to the right.
  4. Position the outer flange plate on the wheel.
  5. Press and hold the brake pedal to keep the wheel from spinning.
  6. Tighten the wingnut.
  7. Use a plastic scraper tool to remove all existing wheel weights. Discard the wheel weights.
    Informational PurposesAn informational icon, calling your attention
    Note
    Thoroughly clean all adhesive residue.
  8. Input the vehicle and wheel information into the balancer.
  9. Attach the air chuck to the valve stem, then set the correct pressure on the touchscreen. The balancer automatically adjusts the tire pressure.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the tire sticker values displayed on the door jam.
  10. Disconnect the air chuck from the valve stem.
  11. Make sure that the balancer is in Road Force mode, the road force limits are set to "P" (passenger car), and SmartWeight is enabled.
  12. Lower the balancer hood. The balancer checks the road force and balance.
    • If the road force is below the limit (Radial Force Peak to Peak = 105 N), go to step 13.
    • If the road force is above the limit:
    1. Hold the dataset arms against the rim at the points that best approximate where the bead of the tire sits on the wheel while the balancer checks the rim runout.
    2. Mark the locations on the wheel and the tire as shown by the balancer.
    3. Transfer the wheel from the balancer to the tire changer.
    4. Partially dismount the tire from the wheel so that the tire can rotate freely relative to the wheel. See Tire - Front - LH (Dismount and Mount).
    5. Match-mount the tire on the wheel: Hold the tire stationary while rotating the wheel until the marks line up. See Tire - Front - LH (Dismount and Mount).
    6. Transfer the wheel to the balancer.
    7. Repeat the previous steps to check the road force and balance.
  13. Install the wheel weights:
    1. Touch START. The balancer rotates the wheel and projects a red line on the center of the proper weight position.
    2. Press and hold the brake pedal to keep the wheel from spinning.
    3. Clean the wheel surface thoroughly and allow it to dry.
    4. Apply the weights specified by the balancer, centered on the red line.
  14. Repeat step 13 to install additional weights, if prompted by the balancer.
  15. Lower the hood. The balancer checks the balance again. Follow the on-screen instructions if the wheel is still not balanced.
  16. Record the road force on the Repair Order.
  17. Press and hold the brake pedal to keep the wheel from spinning.
  18. Loosen the wingnut and remove the outer flange plate from the wheel.
  19. Remove the wheel from the balancer.