Seat Track Assembly - 1st Row - RH (Remove and Replace)
Correction code
13010202
0.72
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See Personal Protection to make sure wearing proper PPE when
performing the below procedure. See Ergonomic Precautions for safe and healthy working practices.
Remove
- Remove front passenger seat from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).
- Remove the front passenger seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
-
Release the connector lock, and then
disconnect the electrical connector from the pretensioner.
Figure 1. LH seat shown; RH seat similar - Remove the front passenger seat inboard side shield. See Side Shield - Inboard - Driver Seat (Remove and Replace).
-
Disconnect the electrical connector
from the 1st row buckle.
Figure 2. LH seat shown; RH seat similar -
Position the seat to access the
underside of the seat.
NoteProtect the seat cushion from damage as necessary.
-
Disconnect the seat track position
sensor connector.
-
Release the clip that attaches the
track motor harness to the track motor housing.
-
Disconnect the LH front seat track
motor connector.
-
Remove and discard the inboard bolts
(x2) that attach the seat track to the seat cushion frame.23 Nm (17.0 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T50 socket
-
Remove the outboard bolts (x2) that
attach the seat track to the seat cushion frame, and then set the seat track assembly on
a flat surface.23 Nm (17.0 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T50 socket
-
Remove and discard the patchbolt that
attaches the buckle to the seat track, and then remove the buckle.
TIpUse of the following tool(s) is recommended:
- Torx T50 socket
- 3/8 in std ratchet
- 3/8 in torque wrench (installation only)
- 3 in extension
Figure 3. LH seat shown; RH seat similar -
Remove and discard the bolt that
attaches the pretensioner to the seat track, and then remove the pretensioner from the
assembly.40 Nm (29.5 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T50 socket
- 3/8 in std ratchet
- 3/8 in torque wrench (installation only)
- 3 in extension
Figure 4. LH seat shown; RH seat similar -
Remove the screw that attaches the
seat track position sensor to the seat track assembly, and then remove the sensor from
the assembly.
TIpUse of the following tool(s) is recommended:
Figure 5. LH seat shown; RH seat similar
Install
-
Position the seat track position
sensor to the seat track assembly, and then install a new screw that attaches the sensor
to the assembly.
TIpUse of the following tool(s) is recommended:
Figure 6. LH seat shown; RH seat similar -
Position the pretensioner to the seat
track, and then install a new bolt that attaches the pretensioner to the seat
track.40 Nm (29.5 lbs-ft)NoteAlign the pretensioner guide pin to the seat track.TIpUse of the following tool(s) is recommended:
- Torx T50 socket
- 3/8 in std ratchet
- 3/8 in torque wrench (installation only)
- 3 in extension
Figure 7. LH seat shown; RH seat similar -
Position the buckle onto the seat
track assembly, and then install the patchbolt that comes with the new seat belt buckle
to attach the buckle to the seat track.40 Nm (29.5 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T50 socket
- 3/8 in std ratchet
- 3/8 in torque wrench (installation only)
- 3 in extension
Figure 8. LH seat shown; RH seat similar -
Position the new seat track assembly
to the seat cushion frame.
-
Install the outboard bolts (x2) that
attach the seat track to the seat cushion frame.23 Nm (17.0 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T50 socket
-
Install new inboard bolts (x2) that
attach the seat track to the seat cushion frame.23 Nm (17.0 lbs-ft)TIpUse of the following tool(s) is recommended:
- Torx T50 socket
-
Connect the LH front seat track motor
connector.
-
Install the clip that attaches the
seat track harness connector to the seat track motor.
-
Connect the seat track position sensor
connector.
- Return the seat back to the upright position.
-
Connect the buckle connector.
Figure 9. LH seat shown; RH seat similar - Install the front passenger seat inboard side shield. See Side Shield - Inboard - Driver Seat (Remove and Replace).
-
Connect the pretensioner electrical
connector.
Figure 10. LH seat shown; RH seat similar - Install the front passenger seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
- Install the front passenger seat. See Seat Assembly - 1st Row - LH (Remove and Replace).