2025-07-31

Link - Lateral - Lower - Front - LH (Remove and Replace)

Correction code 31013402 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2025-07-22: Updated the torque of the bolts that attach the LH front lower lateral link to the front subframe to 190 Nm.
  • 2024-04-15: Added instructions for replacing the bolts that attach the front lower lateral link to the subframe on RH side, if not yet replaced.
  • 2024-01-05: Added new bolts (x2) that attach the front lower lateral link to the subframe. These bolts are one time use and are now torqued to 135 Nm.
  • 2024-01-11: Updated the information about the bolts (x2) that attach the front lower lateral link to the subframe. The bolts without nylon must be replaced while the bolts with nylon can be reused.
Figure 1. Model 3 shown; Model Y similar
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Torque Specifications

Table 1. Torque Specifications: Link - Lateral - Lower - Front - LH (Remove and Replace) / Links - Lateral - Lower - Front - Pair (Remove & Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Precote 85 Patch Bolts (x2) that attach the LH front lower lateral link to the front subframe
190 Nm (140.1 lbs-ft)
  • 21 mm socket
Replace 2123635-00-A
Nylon Patch Bolts (x2) that attach the LH front lower lateral link to the front subframe (old version)
135 Nm (99.6 lbs-ft)
  • 21 mm socket
Replace 1109912-00-B
Bolt and nut that attach the LH strut to the LH front lower lateral link
106 Nm (78.2 lbs-ft)
106 Nm (78.2 lbs-ft)
  • 21 mm socket
Reuse
Nut to attach the LH front lower lateral link to the knuckle
180 Nm (132.7 lbs-ft)
  • 22 mm socket
Replace 1109263-00-B or newer
Bolt that attaches the LH front brake rotor to the knuckle
5 Nm (3.7 lbs-ft)
  • 10 mm socket
Reuse

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  3. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  4. Remove and discard the bolts (x2) that attach the LH front lower lateral link to the subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  5. Remove the bolt and nut that attach the LH strut to the LH front lower lateral link, and then remove the LH front lower lateral link from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  6. Remove and discard the nut that attaches the LH front lower lateral link to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    If the impact gun does not remove the nut, use a 3/8 in ratchet with a Torx T45 socket to counter-hold the inner bolt, and then remove the nut with a 22 mm combination wrench.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 22 mm socket

Install

  1. Position the LH front lower lateral link into the vehicle, and then hand-tighten new bolts (x2) that attach the LH front lower lateral link to the front subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  2. Install a new nut that attaches the LH front lower lateral link to the knuckle.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 22 mm socket
  3. Hand-tighten the bolt and nut that attach the LH strut to the LH front lower lateral link.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  4. Tighten the bolts that attach the LH front lower lateral link to the front subframe.
    1. For 2123635-00-A:
      190 Nm (140.1 lbs-ft)
    2. For 1109912-00-B, use only if 2123635-00-A is not available:
      135 Nm (99.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  5. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Remove the bolt that attaches the LH front brake rotor to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Install a hub jack adapter onto the LH front hub, and then use a support stand to support the LH front suspension at ride height (423 mm).
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure from bottom of fender to center of axle as a check to make sure LH suspension is set close to ride height.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Hub Jack Adapter - 1459409-00-A
  8. Tighten the bolts that attach the LH strut to LH front lower lateral link, and then mark the bolt and nut with a paint pen.
    106 Nm (78.2 lbs-ft)
    106 Nm (78.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  9. Remove the support stand and hub jack adapter from the vehicle.
  10. Install the bolt that attaches the LH front brake rotor to the knuckle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  12. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See Alignment Requirement - Suspension.