17/10/2023 18:55:44

Link - Aft - Upper - Rear - LH (Remove and Replace)

Correction code 3103030032 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1457016-00-A KIT, SPRING COMPRESSOR, GEDORE
  • 1137855-00-A TOOL, REAR RIDE HEIGHT TORQUE, MODEL 3
  • 1081765-00-A 3/4 TON UNDERHOIST STAND
  • 1459409-00-A ADAPTER, HUB JACK, MODEL 3

Torque Specifications

Table 1. Torque Specifications: Link - Aft - Upper - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt and nut that attach the LH rear upper aft link to the LH rear suspension knuckle
134 Nm (98.8 lbs-ft)
  • 21 mm combination wrench
  • 21 mm socket
  • Flex head ratchet/flex head torque wrench
 Reuse
Bolt and nut that attach the LH rear upper aft link to the subframe
134 Nm (98.8 lbs-ft)
  • 21 mm combination wrench
  • 21 mm socket
  • Flex head ratchet/flex head torque wrench
 Reuse

Remove

  1. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  2. Remove the LH rear suspension cover. See Cover - Rear Suspension - LH (Remove and Replace).
  3. Remove the bolt and nut that attach the LH rear upper aft link to the LH rear suspension knuckle.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm combination wrench
    • 21 mm socket
    • Flex head ratchet/flex head torque wrench
  4. Remove the bolt and nut that attach the LH rear upper aft link to the subframe.
    Tip: Use of the following tool(s) is recommended:
    • 21 mm combination wrench
    • 21 mm socket
    • Flex head ratchet/flex head torque wrench
  5. Remove the LH rear upper aft link from the vehicle.

Install

  1. Position the LH rear upper aft link onto the subframe, and then install and hand-tighten the bolt and nut.
  2. Position the LH rear upper aft link onto the knuckle, and then install and hand-tighten the bolt and nut.
  3. Install a spring compressor onto the LH rear suspension spring:
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Springs in a compressed state are under large amounts of energy. Refer to the Tool Profile for the spring compressor kit prior to performing this step for additional warnings and cautions.
  4. Remove the bolt that attaches the LH rear brake rotor to the hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  5. Install the hub jack adapter onto the LH rear hub and hand-tighten the lug nuts (x5).
  6. Position and raise the underhoist stand to simulate the suspension at ride height.
  7. Adjust the underhoist stand and/or spring compressor until the lower beam of the rear ride height torque tool rests against the bottom edge of the lower aft link, as illustrated.
  8. Measure the distance between the bottom of the quarter panel and the center of the rear axle to make sure that the rear suspension is set to ride height. The distance should measure 378 mm.
  9. Tighten the bolt and nut that attach the LH rear upper aft link to the subframe. Mark the bolt with a paint pen.
    134 Nm (98.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 21 mm combination wrench
    • 21 mm socket
    • Flex head ratchet/flex head torque wrench
  10. Tighten the bolt and nut that attach the LH rear upper aft link to the knuckle, and then mark the bolt and nut with a paint pen.
    134 Nm (98.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 21 mm combination wrench
    • 21 mm socket
    • Flex head ratchet/flex head torque wrench
  11. Remove the underhoist stand from underneath the LH rear suspension.
  12. Remove the lug nuts (x5) that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
  13. Install the bolt that attaches the LH rear brake rotor to the LH rear hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  14. Remove the spring compressor from the LH rear suspension spring:
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Be careful while unloading the spring. Hold the spring horizontally and facing away from you.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Springs in a compressed state are under large amounts of energy. Refer to the Tool Profile for the spring compressor kit prior to performing this step for additional warnings and cautions.
  15. Install the LH rear suspension cover. See Cover - Rear Suspension - LH (Remove and Replace).
  16. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  17. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.