17/10/2023 18:51:08

Switch - Interior Door Release - Rear - LH (Remove and Replace)

Correction code 1513020052 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Switch - Interior Door Release - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH rear door interior handle to the door trim panel
1 Nm (.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • Torx T20 socket
  • Ratchet/torque wrench
 Reuse
Bolt that attaches the interior door release switch to the LH rear door trim panel
1 Nm (.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • Torx T20 socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Open the LH rear door.
  2. Lower the LH rear window.
  3. Remove the LH rear door puddle light. See Puddle Lamp - Rear Door (Remove and Replace).
  4. Remove the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  5. Release the tabs (x3), and then remove the NVH pad from the LH rear door trim panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend an assistant to hold the door trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not remove the door electrical connector and clips.
  6. Disconnect the electric release switch connector.
  7. Remove the bolts (x2) that attach the interior door handle to the LH rear door panel trim.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  8. Remove the bolt that attaches the electric release switch to the door handle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently release the door handle to gain access to the bolt location.
  9. Apply masking tape around the work area to protect the door trim panel.
  10. Pry open the front portion of interior door handle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure there is enough space to remove the interior door release switch.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  11. Release the tabs and then remove the interior door release switch from the door trim panel.

Install

  1. Fasten the tabs that attach the interior door release switch onto the door trim panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  2. Secure the front portion of the interior door handle onto the door trim panel.
  3. Remove the masking tape from the door trim panel.
  4. Install the bolt that attaches the electric release switch to the door handle.
    1 Nm (.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently release the door handle to gain access to the bolt location.
  5. Install the bolts (x2) that attach the interior door handle to door panel trim.
    1 Nm (.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  6. Connect the electric release switch connector.
  7. Install the NVH pad onto the rear door trim panel and secure the pad with the tabs (x3).
  8. Install the LH rear door puddle light. See Puddle Lamp - Rear Door (Remove and Replace).
  9. Install the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).